Data Table; Heat-Up Table; Country-Specific Approvals And Certifications; Extreme Operating And Fault Conditions - STIEBEL ELTRON SHU 10 SLi Bedienung Und Installation

.CZ`<<`.HC
ZT.%.`.HC

17.3 Data table

B ®¼ù
Type
Part number
Application
H ¼ | ê Ö ®¼ |êù
Nominal capacity
Mixed water volume 40 °C (15 °C / 65 °C)
Rated output
Power connection
Approximate temperature setting
Minimum
Maximum
Maximum temperature limit
Permissible operating pressure
Maximum flow rate
IP rating to EN 60529
Container (material)
Connection (material)
Resistance
Torque value of the flange screws
ê ¼ ê | ® ¼êÖä
Height
Width
Depth
Water connection (male thread)
Power cable, length
Approx. weight
Approx. wet weight

17.3.1 Heat-up table

The heat-up period depends on the degree of scaling and the
residual heat. For the heat-up time for a cold water supply of 10 °C
and a maximum temperature setting, see the diagram.
x Temperature settings in °C
y Duration in min
1 3.3 kW / 15 l appliance
2 2 kW / 10 l appliance
3 2 kW / 15 l appliance
Example 10 l - appliance:
Temperature setting = 65 °C
Heat-up time = approx. 18 min
’Z+e ’ Z+
Z¼|ù¼® ¼ ¼® |ùù | ¼ ä¼| ¼
SHU 10 SLi SHU 10 SL GB
229473 229474
Undersink Undersink
l 10 10
l 19 19
kW 2.0 2.0
V 1/N/PE ~ 230 1/N/PE ~ 230
°C 35 35
°C 82 82
°C 38 / 45 / 55 / 65 38 / 45 / 55 / 65
MPa 0.7 0.7
l/min 10 10
IP 24 D IP 24 D
Steel, enamelled on Steel, enamelled on
the inside the inside
Brass, nickel-plated Brass, nickel-plated Brass, nickel-plated Brass, nickel-plated Brass, nickel-plated
Ω 560 560
Nm 6±1 6±1
mm 504 504
mm 295 295
mm 275 275
G ⅜" A G ⅜" A
mm 650 650
kg 7.6 7.6
kg 17.6 17.6
3
2
1
SH 10 SLi
229476
Oversink
10
19
2.0
1/N/PE ~ 230
35
82
38 / 45 / 55 / 65
0.7
10
IP 24 D
Steel, enamelled on
the inside
560
6±1
598
295
275
G ½" A
650
7.6
17.6
17.3.2 Country-specific approvals and certifications
Test symbols can be seen on the type plate.

17.4 Extreme operating and fault conditions

In case of faults, a peak temperature up to 105 °C may briefly
occur in the system.
SH 15 SLi SH 15 SL GB
229478 229480
Oversink Oversink
15 15
28 28
2.0 3.3
1/N/PE ~ 230 1/N/PE ~ 230
35 35
82 82
38 / 45 / 55 / 65 38 / 45 / 55 / 65
0.7 0.7
12 12
IP 24 D IP 24 D
Steel, enamelled on Steel, enamelled on
the inside the inside
560 560
6±1 6±1
598 598
316 316
295 295
G ½" A G ½" A
650 650
10.5 10.8
25.5 25.8
qqq Z`. <é<`VHC HB