Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL GC-SC 36/31 Li-Solo Originalbetriebsanleitung

long trousers. Always scarify along the incline (not
up and down). For safety reasons, the scarifi er
may not be used to scarify inclines whose gradi-
ent exceeds 15 degrees.
Use special caution when backing up and pulling
the scarifi er (tripping hazard)!
Tips for proper working
It is recommended that you overlap scarifying
paths a little.
There are two markings on the housing (Fig. 2/
Item A) which correspond to the width of the sca-
rifi er and aerator rollers.
Try to scarify in straight lines for a nice, clean look.
Insodoing, the aeration swaths should always
overlap each other by a few centimeters in order
to avoid bare strips.
If you use the catch bag which is available as an
option, it has to be emptied as soon as grass clip-
pings start to trail behind during scarifying.
Danger! Before taking off the grass basket,
switch off the motor and wait until the roller
has come to a stop.
To remove the grass basket, lift up the ejector fl ap
with one hand, while unhooking the basket with
the other.
How frequently you should scarify your lawn is
determined primarily by the speed at which the
grass grows and the hardness of the soil.
Keep the underside of the equipment clean and
remove soil and grass build-up. Deposits make it
more diffi cult to start the aerator and decrease the
quality of the scarifying.
Always scarify along inclines (not up and down).
Switch off the motor before doing any checks on
the roller.
Danger!
The roller rotates for a few seconds after the
motor is switched off . Never attempt to stop the
roller. In the event that the rotating roller strikes
an object, immediately switch off the equipment
and wait for the roller to come to a complete stop.
Then inspect the condition of the roller. Replace
any parts that are damaged (see section 7.3).
Anl_GC_SC_36_31_Li_Solo_SPK9.indb 24 Anl_GC_SC_36_31_Li_Solo_SPK9.indb 24
GB
Tips on aerating properly with the aerator
roller available as an option.
The way of working for aerating is the same as for
scarifying.
You should therefore observe these safety inst-
ructions and notes on working practice.
7. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the safety plug before performing
any adjusting, repair, maintenance or cleaning
work on the equipment. Make sure that the spike
drum is not rotating.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
7.2 Maintenance
•
A worn out or damaged cutting unit should be
replaced by an authorised expert (see adress
on the warranty certificate).
•
Take care that all fastening elements (screws,
nuts, etc.) are firmly tightened, so that you
can work safely with the scarifier.
•
Store the scarifier in a dry place.
•
For longer life, all screw-fastened parts, such
as wheels and axles should be cleaned and
subsequently oiled.
•
Regular servicing of the scarifier not only
secures longer endurance and performance,
but also contributes to an accurate and simp-
le scarification of your lawn.
•
At the end of the season, carry out a general
check of the scarifier, and remove all residue
collected. Before the start of every season, it
is absolutely necessary to check the state of
the scarifier. Contact our Customer Service
- 24 -
20.09.2018 15:41:36 20.09.2018 15:41:36