Specifications; Safety Instructions - Makita 6300-4 Betriebsanleitung

ENGLISH
1 Side grip
2 Tighten
3 Chuck key
4 Sleeve

SPECIFICATIONS

Model
Capacities
Steel ............................................................ 13 mm
Wood ........................................................... 30 mm
–1
No load speed (min ) ............. 500/600/1,100/1,300
Overall length ............................................... 385 mm
Net weight ........................................................3.2 kg
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.

SAFETY INSTRUCTIONS

Warning! When using electric tools, basic safety
precautions should always be followed to reduce
the risk of fire, electric shock and personal injury,
including the following. Read all these instruc-
tions before attempting to operate this product
and save these instructions.
For safe operation:
1. Keep work area clean
Cluttered areas and benches invite injuries.
2. Consider work area environment
Don't expose power tools to rain. Don't use
power tools in damp or wet locations. Keep work
area well lit. Don't use power tools in presence of
flammable liquids or gases.
3. Guard against electric shock
Prevent body contact with grounded surfaces
(e.g. pipes, radiators, ranges, refrigerators).
4. Keep children away
Do not let visitors contact tool or extension cord.
All visitors should be kept away from work area.
5. Store idle tools
When not in use, tools should be stored in dry,
high, or locked-up place, out of the reach of chil-
dren.
4
Explanation of general view
5 Ring
6 Switch trigger
7 Lock button
8 Speed change switch (A)
6.
6300-4
7.
8.
9.
10. Connect dust extraction equipment
11. Don't abuse cord
12. Secure work
13. Don't overreach
14. Maintain tools with care
15. Disconnect tools
16. Remove adjusting keys and wrenches
17. Avoid unintentional starting
9 Speed change switch (B)
10 Limit mark
11 Brush holder cap
12 Screwdriver
Don't force tool
It will do the job better and safer at the rate for
which it was intended.
Use right tool
Don't force small tools or attachments to do the
job of a heavy duty tool. Don't use tools for pur-
poses not intended; for example, don't use circu-
lar saw for cutting tree limbs or logs.
Dress properly
Do not wear loose clothing or jewelry. They can
be caught in moving parts. Rubber gloves and
non-skid footwear are recommendemd when
working outdoors. Wear protective hair covering
to contain long hair.
Use safety glasses and hearing protection
Also use face or dust mask if cutting operation is
dusty.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used.
Never carry tool by cord or yank it to disconnect it
from receptacle. Keep cord from heat, oil and
sharp edges.
Use clamps or a vise to hold work. It's safer than
using your hand and it frees both hands to oper-
ate tool.
Keep proper footing and balance at all times.
Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating
and changing accessories. Inspect tool cords
periodically and, if damaged, have repaired by
authorized service facility. Inspect extension
cords periodically and replace if damaged. Keep
handles dry, clean and free from oil and grease.
When not in use, before servicing, and when
changing accessories such as blades, bits and
cutters.
Form the habit of checking to see that keys and
adjusting wrenches are removed from tool before
turning it on.
Don't carry plugged-in tool with finger on switch.
Be sure switch is off when plugging in.