Accessories; Routine Maintenance; After Every Use; Every Week - Femi 2200 SPECIAL Gebrauchsanleitungen Und Wartung

5

ACCESSORIES

5.1 CHOISE OF BLADE
Your sawing machine is equipped with a bi-metal blade
measuring 2140x19x0.9 mm with variable toothing 6/10
teeth per inch, for use in the majority of cuts possible with
this machine.
For special requirements (see cutting table ), for example,
for cutting large solid sections or profi led sections or corner
pieces of small thickness, there are also blades avail-able
with 4/6 toothing or 14 teeth per inch.
MATERIAL: ............... M42 (steel for springs + steel HSS)
EXTENSION: ..................................................... mm 2140
HEIGHT: ................................................................ mm 19
THICKNESS: ........................................................ mm 0,9
TOOTHING: ................................................standard 6/10
...................................... optional 4/6 - 14
6 MAINTENANCE
6.1

ROUTINE MAINTENANCE

The interventions of routine maintenance which can also
be carried out by unskilled personnel are described in this
paragraph and in the previous ones.
WARNING: Before any maintenance work,
disconnect the machine plug from the mains.
WARNING: During the maintenance works,
always wear protective gears (protective goggles
and gloves of adequate size).

AFTER EVERY USE

• If need be, remove any chip in the cutting area and on
the sawblade guides. We recommend the use of a brush
or an exhaust fan.
WARNING: The use of compressed air is
absolutely prohibited !!!
• Check for the correct height of suction of the pump from
the tank and make sure that the coolant comes out from
both dispensers placed on the sawblade guides.

EVERY WEEK

• Lubricate the slides of the sliding blade guide and the
swivel support and the nut screw of the chuck.
• Remove the chips from the area of the coolant collecting
fi lter.
• Clean the sawblade guide plates with a brush.
• Check that all machine safety guards are not damaged
and that the start push button works properly.
• If the saw is not used for a long period of time, clean
and store it in a place free from humidity. In this case,
it is advisable to loosen the blade in order not to keep it
uselessly tensioned.
2200_PARTI COMUNI.indd 13 2200_PARTI COMUNI.indd 13
6.2 REPLACEMENT OF THE COOLANT
The refrigerating emulsion must be replaced every 500
hours.
• Remove the plug from the wall outlet to disconnect the
machine.
• Empty the pump tank by removing cap C (Fig. 11) and
remove the chips inside of it, if any.
• Prepare the new emulsion, as specifi ed at item 4.1 and
pour it inside the tank. Make sure that the emulsion is
properly disposed of.
• For emulsion disposal, please refer to item 6.4.
6.3

AFTER-SALES SERVICE

In case of repair under guarantee, the receipt/purchase
invoice must be presented together with the machine.
The absence of this document will invalidate the guarantee
applied to the machine.
Should the presence of skilled personnel be necessary
for extraordinary maintenance work or in case the repair
is effected both under guarantee or after it, please always
contact an authorised centre or the dealer where you
purchased the machine, if an authorised centre is not
present in your region.
When you contact the after-sales service or the dealer,
always advise the purchase date of the machine and its
serial number engraved on the CE.
When ordering spare parts, information about the machine's
model, the serial number as well as the part code listed in
the spare parts table must always be given to the After-
sales Service.
6.4 DISPOSAL OF THE MACHINE AND
PACKAGING
NFORMATION FOR USERS
In accordance with art. 13 of Legislative Decree
25th July 2005, no. 151 "Implementation of
Directives 2002/95/EEC, 2002/96/EEC and
2003/108/EEC, relative to reducing the use
of hazardous substances in electrical and
electronic appliances and the disposal of
waste", please take note of the following:
• The crossed out wheelie bin symbol found on the
appliance or on the packaging, indicates that the product
must be disposed of separately from ordinary household
waste when it reaches the end of its working life.
• The user must consign the unwanted appliance to
an authorized differentiated waste disposal centre for
electrical and electronic goods, or alternatively, hand
it over to the relative dealer on purchasing a new
appliance of the same type on the basis of a one to
one ratio.
13
21/10/2008 15.27.42 21/10/2008 15.27.42