Dismantling And Replacement - Texas XC160-102HC Bedienungsanleitung

All checks, adjustments and replacements not
described in chapters 6.3 and 6.4 of this manual
must be carried out by your Dealer or a
specialized Service Center. Both have the
necessary knowledge and tools to ensure that
the work is carried out correctly without affecting
the safety of the machine.
6.2.1 Summary of main situations where servicing
operation may be required
Whenever...
The blades vibrate
The blades tear the grass
and the lawn becomes
yellow
The cut is uneven
The blades engage in an
abnormal way
The machine does not
brake
Forward movement is
erratic
6.2.2 Engine
Follow all the instructions in the engine manual. To
empty the engine oil, unscrew the oil plug when refitting
the plug, make sure the seal is positioned correctly.
6.2.3 Battery
The battery must be carefully maintained to ensure long
life. The machine battery must always be charged:
•
Before using the machine for the first time after
purchase
•
Before leaving the machine disused for a long
period
•
Before starting up the machine after a long period
of disuse
Carefully read and observe the battery recharging
instructions in the booklet provided with the battery.
Failure in following the instructions or in charging the
battery could permanently damage the battery cells.
A flat battery must be recharged as soon as possible.
Charger is not included with machine!
Battery will re-charge when tractor is used.
Recharging must be done using a battery
charger at constant voltage. Other recharging
systems can irreversibly damage the battery.
6.3 Adjustments of deck
6.3.1 Cutting deck alignment
See Fig. 28
The cutting deck should be properly set to obtain a
good cutting result.
For achieving good results from cutting the front
part should always be 5-6 mm lower than the rear
part.
•
Place the machine on flat ground and
check the tire pressure
•
Put 26 mm blocks under the front
edge of the deck and 32 mm blocks
under the rear edge.
You will need to...
Contact Your Dealer
Replace blades /
Contact Your Dealer
Align the cutting deck
(☛ 6.3.1)
Contact Your Dealer
Contact Your Dealer
Contact Your Dealer
•
Adjust the nut 1 and nut 2 to keep the deck in touch
with the 26 mm blocks.
•
Adjust the nut 3 to keep the deck in touch with the
32 mm blocks.

6.4 Dismantling and replacement

6.4.1 Replacing wheels
See Fig. 29
Stop the machine on flat ground and put a block
under a load-bearing part of the frame on the side
that the wheel is to be changed.
The wheels are held by a snap ring which can be
eased off with a screwdriver.
If you have to replace one or both rear wheels,
make sure they have the same diameter, and check
that cutting deck is horizontal to prevent an uneven
cut.
Before remounting the wheel, apply grease to
the axle. Put the snap ring and supporting
washer back in place.
6.4.2 Replacing and repairing the tires
The tires are "tubeless" and so all punctures must be
repaired by a tire repairer following the procedures
required for this kind of tire.
6.4.3 Replacing the bulbs
The bulbs (12V/18W) have a bayonet fitting and are
installed in the bulb holder which can be taken out by
turning it anti-clockwise.
New light bulb has art. no. 439662
6.4.4 Replacing a fuse
See Fig. 30
The machine is fitted with 15A fuses.
When it blows, the machine stops, the dashboard
light switches off and the battery gradually runs
out. The machine will have problems starting.
Remove the fuse and replace with a same type fuse.
A blown fuse must always be replaced by one
of the same types and ampere rating, and never
with one of another rating.
6.4.5 Dismantling, replacing and remounting the
blades
See Fig. 31
Always wear work gloves when handling the
blades. Before you inspect or remove the blade,
stop the engine and disconnect the wire to the
spark plug.
Damaged or bent blades must always be
replaced, never try to repair them!
ALWAYS USE ORIGINAL BLADES!
Make sure the blades are correctly balanced.
Make sure you put them back in the right place
by referring to the code stamped on the outside
of each blade.
1) Dismantling blades
1a = screw with right thread (loosen anti-clockwise)
1b = screw with left thread (loosen clockwise)
31