Air Filter; Blade; Spark Plug; Storage And Maintenance - Texas Razor 4610 Bedienungsanleitung

Air Filter

The air filter should be inspected and cleaned regularly.
If the filter has not been cleaned for a long time, the
engine's power will drop.
See Illustration A2
1. Clean around the air filter before removing the
cap.
2. Push the two flaps down and gently pull the
cover
3. Carefully remove the paper filter and inspect it.
Brush it with a soft brush. If it is very dirty,
replace it. Be careful that no dirt gets into the
inlet.
4. Wash the black foam element in the right side
in warm water and soap.
5. Press the water out of the foam element and
let it dry. Put a few drops of SAE-30 oil on the
filter to moisten it lightly. Carefully squeeze
any surplus oil out of the foam element and
reattach.
6. Please note that all parts are assembled
correctly and properly closed, as shown in the
picture.

Blade

Inspection of the blade

Tilt the mower with the front upwards.

Inspect blade for damage, cracks or excessive
rust or corrosion.

Check that the blade bolt is tightened.
Note: A dull blade can be sharpened! But a blade that
is worn, bent, cracked or otherwise damaged must be
replaced.
Removing the blade: See illustration A3
If you remove the blade to sharpen or replace it, you
must use a torque wrench and some heavy gloves to
protect your hands.
1. Loosen the blade bolt. Use a piece of wood to
prevent the blade from turning around.
2. Remove the bolt, washer, blade and blade
holder in that order
3. Sharpen or replace the blade.
4. Insert the blade holder, blade, washer and bolt
in that order.
5. Tighten the blade bolt. Use a piece of wood to
prevent the blade from turning around.
Warning: A blade must be sharpened so it is in
100 % balance, otherwise it may cause vibrations that
could damage the engine. Damage to engine due to
faulty sharpening is not covered by warranty. We
therefore recommend letting a service center sharpen
the blade.

Spark plug

1. Remove the spark plug.
2. Brush off dirt from the spark plug.
3. Use a spark plug wrench to loosen the spark
plug.
4. Check the insulation is intact.
5. Clean the spark plug with a wire brush.
6. Measure the electrode, taking care not to
damage the electrode.
7. The distance should be: 0.7 to 0.8 mm
8. If the spark plug is undamaged refit or replace.
TEX-Part 40-11294
9. Reattach the spark plug.

Storage and maintenance

Maintain your lawnmower: Check all bolts, screws,
nuts and deck. Always make sure that the blade is
sharp. It's a good idea to take your lawn mower to an
annual service check with your authorized service
dealer. See your nearest service center at
www.texas.dk.
Storage: After use the lawnmower kept in a dry and
clean room. Clean the machine after every use. Grass
and dirt must be removed from the underside of the
deck. By tipping the mower (for cleaning) is
recommended to tilt the front up (max. 45 degrees). If
you tilt it sideways, the carburetor and air filter always
face upwards, since oil may run out and destroy the
engine. Be aware that removing the spark plug before
the mower maintenance.
Winter storage: Empty the fuel tank and let the engine
run until the gasoline in the carburetor is used up. Spark
plug removed. Remove the spark plug and add a
teaspoon of oil (engine oil) in the hole. Pull the starter to
distribute oil. Mount the spark plug, but no cable.
Change oil cf. the section above. Finally, the mower
cleaned thoroughly. Dip a cloth in oil and lubricating the
various parts to prevent rust.

Warranty

•
There is 2 years warranty on your lawnmower.
•
The warranty covers materials and/or
workmanship.
•
No guarantee for damage due to wear and the
poor treatment and lack of maintenance.
•
The warranty does not cover cleaning the fuel
system, replacement/adjustment of the starting
cord, starter springs, spark plugs, blade/blade
holder, straps and cables or any battery, as
these are a result of ordinary wear.
•
The warranty does not cover if unoriginal parts
have been used.
•
Whether a case is a warranty claim or not is
determined in each case by an authorized
service center.
•
Your receipt is your warranty note, why it
should always be kept safe.
•
If you start the engine without adding oil, it will
be damaged and cannot be repaired and
therefore not covered by the warranty.
REMEMBER: The purchase of spare parts as well as
any request for warranty repair, model number and
serial number should always been informed. They can
be found on the CE-label on the machine! I
10