To Fill The Gun From Bulk Container; To Fill The Gun With A Filler Pump - Lincoln 1800 Gebrauchsanweisungen

To Fill The Gun from Bulk Container
1. Remove pump assembly from grease tube
assembly.
2. Pack lubricant into cavity of the pump as­
sembly.
-,' Y/0#9*'*@#'."#/'#/5'.)'*@#'?9#(0#'*>O#'
(00#=O4+'%/*.'4>O9%$(/*'T0##'_%?,'-U,'!4.74+'
pull the follower handle back while pushing
the grease tube assembly deeper into the
lubricant to prevent air pockets from being
pulled into the grease tube assembly.
4. When the follower rod is fully extended,
pull it sideways to latch the rod groove
into the keyhole slot in the grease tube
assembly cap.
5. Loosely assemble the pump assembly to
the grease tube assembly. Release the fol­
lower rod from the grease tube assembly
cap and disengage the follower rod from
the follower by rotating the follower handle.
Push the follower rod into the grease tube
assembly. Slowly unscrew the grease tube
assembly from the pump assembly until
4>O9%$(/*'..A#0')9.='*@#'%/*#9)($#,']%?@*#/'
grease tube assembly into the pump as­
sembly.
_%?>9#'-
Form 403865
Models 1800, 1842, 1842E, 1844, 1844E
To Fill The Gun with a Filler
Pump
1. Engage the follower rod with the follower
by rotating the follower handle.
B,' Y/0#9*'*@#'?>/'K#/*WO>4\'&44'K(4K#'%/*.'*@#'
&44#9'">="'0.$\#*'T0##'_%?,'1U,'
-,' S"#9(*#'*@#'&44#9'">="'*.'&44'*@#'$./*(%/#9,'
When the follower rod groove is exposed,
*@#'?9#(0#'*>O#'(00#=O4+'%0'&44#5,']@#').4­
lower rod will be extended approximately 8
%/$@#0'TBF'$=U,'`.'/.*'.K#9&44a'
4. Disengage the follower rod from the
follower by rotating the follower handle.
Push the follower rod into the grease tube
assembly.
Remove Air Pocket! Air pocket at grease
inlet will prevent grease from being pumped.
C/0$9#7'*@#'K#/*WO>4\'&44'K(4K#'*7.')>44'*>9/0'*.'
remove small air pockets trapped in this area.
If the air pocket is substantial and no grease
^.70')9.='$.>"4#9'()*#9'*9%??#9'%0'">44#5').9';M'
seconds, see following steps.
To Expel Air Pockets
1. Withdraw the follower rod from the grease tube
assembly cap and engage it with the follower by
rotating the follower handle.
B,' C/0$9#7'*@#'K#/*WO>4\'&44'K(4K#'*7.'*>9/0,''23#9*'
).9$#'./'*@#').44.7#9'@(/54#'>/*%4'?9#(0#'^.70'
*@9.>?@'*@#'."#/%/?'%/'*@#'K#/*WO>4\'&44'K(4K#,
-,'' ]%?@*#/'*@#'K#/*WO>4\'&44'K(4K#,
4. Pull the trigger in short bursts to operate gun
until trapped air is expelled. Disengage the
follower rod from the follower by rotating the
follower handle. Push the follower rod into the
grease tube assembly.
5. If step 2 fails, unscrew the grease tube assem­
O4+';<;WB'*>9/0')9.='*@#'">="'(00#=O4+,
6. Exert force on the follower handle until lubricant
..A#0')9.='*@#'?9#(0#'*>O#'(00#=O4+'(/5'
pump assembly interface.
7. Tighten grease tube assembly into the pump
assembly. Disengage the follower rod from the
follower by rotating the follower handle. Push
the follower rod into the grease tube assembly.
PowerLuber Grease Gun
Figure 4
Page Number ­ 7