Inspection - Lincoln 1800 Gebrauchsanweisungen

Models 1800, 1842, 1842E, 1844, 1844E
PowerLuber Grease Gun

INSPECTION

Visually inspect for damaged, loose or miss­
ing parts. If equipment is worn or damaged,
9#=.K#')9.='0#9K%$#,'V./*($*'(/'(>*@.9%A#5'
service center for damage assessment or
repair.
OPERATION
Changing "L" or "H" Mode
To change the mode of operation:
To prevent damage to the gears in the
transmission, the motor must be com­
pletely stopped before changing the lever
to the "L" or "H" (low or high) mode of
operation.
"L"'T4.7'.>*">*W@%?@'"9#00>9#U
"H"'T@%?@'.>*">*W4.7'"9#00>9#U
When motor is not running, push the lever
(Fig. 1) until letter "L" or "H" will be completely
visible in the window.
In case the lever is not completely shifted/
engaged, hold this lever and bump the switch
to engage gears.
High output is recommended if the tool is
used to lubricate large bearings not requiring
@%?@'"9#00>9#E'O#+./5'-EFFF'8!Y'TBFG'O(9U,'
Also, high output is recommended if tool is
>0#5'*.'9#&44'0=(44'9#0#9K.%90'.)'*@#'(>*.=(*%$'
lubrication systems.
Low output is recommended if the tool is
used in construction, mining applications and
general lubrication. Low output will provide
the maximum pressure of up to 7,000 PSI
(482 bar) the tool is capable of producing.
89%=#'*@#'8.7#9:>O#9'()*#9'#($@'9#&44'.9'
grease cartridge change. Prime the gun
before using it to lubricate grease points.
].'"9%=#E'."#9(*#'*@#'?>/'>/*%4'?9#(0#'^.70'
from the hose. Use vent valve (Fig.1) to expel
air pockets.
Installing Grease Cartridge
1. Unscrew the grease tube assembly from
the PowerLuber.
2. Visually check the follower seal lip direc­
tion before loading a new cartridge. The
follower seal lip must be directed toward
the follower handle or rear side for car­
tridge loading. See Fig. 2. (To change the
Page Number ­ 6
direction of the follower seal, unscrew tube
cap from grease tube assembly and pull on
the handle to remove follower seal from tube.
Flip follower seal over and reassemble.)
-,' 8>44'O($\'./'*@#').44.7#9'@(/54#'(/5'4(*$@'*@#'
follower rod groove into the slot on the tube
cap.
4. Remove the plastic cap from the grease
cartridge and insert cartridge into the
container tube.
5. Remove the pull tab from grease cartridge
and screw grease tube assembly into pump
assembly.
6. Thread grease tube assembly back onto the
Powerhead.
7. Release follower rod from slot. Purge air
from pump. See air purging instructions.
Air pockets in the cartridge lubricant will
cause the gun to lose its prime.
Removing Empty Grease Cartridge
1. Pull back on the follower handle until the
follower rod is fully extended and latch the
follower rod groove into the slot on the tube
cap.
2. Unscrew the grease tube assembly from the
PowerLuber.
-,''V(9#)>44+'9#4#(0#'*@#').44.7#9'@(/54#'*.'#I#$*'
the empty cartridge from container tube.
To Convert Gun to Allow Filling From
Bulk Containter or Filler Pump
1. Unscrew the grease tube assembly cap
from the grease tube assembly. Pull on the
follower handle to extract the follower and
spring from the grease tube assembly.
B,''H9(0"').44.7#9'O#*7##/'*@>=O'(/5').9#&/?#9'
(/5'^%"'*@#').44.7#9'4%"')9.='*@#'9#(9'*.'*@#'
front side.
NOTE. The follower resembles a cup. When
the gun is assembled for use with bulk
lubricant, the cup opens toward the pump
assembly.
-,''N#(00#=O4#').44.7#9'%/*.'?9#(0#'*>O#'(0­
sembly and position with the follower handle
so that the grease tube assembly cap can be
tightened onto the container tube.
Figure 2
Form 403865