Before Starting The Equipment; Assembling The Components; Setting The Cutting Height - EINHELL 51/1 S B&S Betriebsanleitung

Anleitung_RG_PM_51_1_S_SPK7:_
GB
Sound and vibration
L sound pressure level
pA
K uncertainty
pA
L sound power level
WA
K uncertainty
WA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Vibration emission value a = 6.36 m/s
h
K uncertainty = 1.5 m/s
2
Sound and vibration values were measured in
accordance with EN 292-2:1991/A1:1995.
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
Have the appliance serviced whenever
necessary.
Switch the appliance off when it is not in use.
Wear protective gloves.

6. Before starting the equipment

6.1 Assembling the components

Some parts of the mower come disassembled. For
quick and easy assembly, read and follow the
instructions below.
Important! You will need the following additional
tools (not supplied) for assembly, and also for
maintenance work:
A flat oil drip tray (for changing the oil)
A 1 liter measuring jug (oil/petrol resistant)
A petrol can
A funnel (suitable for the tankʼs petrol filler neck)
Household wipes (to wipe up oil/petrol residue;
dispose of these at a filling station)
A petrol suction pump (plastic, available from
DIY stores)
An oil can with hand pump (available from DIY
stores)
24
28.03.2012 13:18 Uhr
Assembly
1. Affix the lower push bar (Fig. 3a/Item 5) to the
mower housing and set the desired working
87.8 dB(A)
height. 3 different working heights are available.
2 dB
Each peg on the lower push bar can be inserted
98 dB(A)
into a hole situated directly opposite to it, on the
2 dB
mower housing, for example A-A (Fig. 3). The
lower push bar must be equally adjusted on both
sides. Now affix the cover (Fig. 3a/Item 23) and
attach the push bar (5) using the square head
screws (15) and the star screws (18) as shown in
Figure 3a.
2
2. Fasten the top push bar to the bottom push bar
using a screw (Fig. 3b/Item 16) and a star screw
(Fig. 3b/Item 18) on each side. Make sure that the
lobes of the screws are folded towards the inside
so that the high speed clamping function remains
operational.
3. Insert the grip of the starter cord (Fig. 3c/Item 4)
into the hook provided for that purpose as shown
in Figure 3c.
4. Fasten the cords to the push bar with the
supplied cable ties (Fig. 3d/Item. 13).
5. The debris bag should be assembled as shown in
Figure 3e. For this, insert the upper lugs of the
debris bag carefully into the openings on the
lower debris bag.
6. Lift the ejector flap (Fig. 4 / Item 8) with one hand
and hook in the grass bag (Fig. 4/Item 7) as
shown in Figure 4

6.2 Setting the cutting height

Important! Adjust the cutting height only when
the engine is switched off and the plug boot has
been pulled.
Before you begin to mow, check to ensure that
the blade is not blunt and that none of the
fasteners are damaged. To prevent any
imbalance, replace blunt and/or damaged blades
as a set only (if applicable). To carry out this
check, first switch off the engine and pull the
spark plug boot.
The cutting height is centrally adjusted with the
cutting height adjustor lever
(Fig. 7/Item 9). Up to 5 different cutting heights
can be selected.
Pull the adjustor lever out and select the desired
cutting height. The lever snaps into the desired
position.
Seite 24