Storage And Transport; Maintenance And Service; Maintenance And Cleaning - Bosch GTS 10 J Professional Originalbetriebsanleitung

OBJ_BUCH-1325-002.book Page 36 Thursday, May 12, 2011 1:51 PM
36 | English
Checking:
The mark of lens 27 must be in a line with the 0° mark of scale
1.
Adjusting:
– Loosen screw 62 using a Phillips screwdriver and align the
clearance indicator alongside the 0° mark.
Adjusting the Level of the Insert Plate (see figure X)
Checking:
The front side of the insert plate 24 must be flush with or
somewhat lower than the saw table; the rear side must be
flush with or somewhat above the saw table.
Adjusting:
– Remove the insert plate 24.
– Adjust the correct level of the four adjusting screws 63
with the Allen key 64.
Adjusting the Tension Force of the Parallel Guide
The tensioning force of the parallel guide 10 can decrease af-
ter frequent usage.
– Tighten the adjustment screw 70 until the parallel guide
can be firmly affixed on the saw table again.

Storage and Transport

Storing Product Features (see figures Y1–Y6)
For storage purposes, certain product features can be se-
curely fastened to the power tool.
– Loosen auxiliary parallel guide 37 from parallel guide 10.
– Attach all loose tool parts to their storage locations on the
housing. (see Table)
Figure Product Feature Storage Location
Y1 Blade guard 6.x Insert into the recess of fixture
33 and tighten with clamping
lever 8.1 or clamping screw 8.2
Y2 "Auxiliary parallel Clip into the holders 65
guide" fastening
kit 38
Y2 Extraction adapter Insert into retaining clamp 66
32
Y3 Ring spanner 22 Fasten in tool depot with
fastening nut 67
Y3 Push stick 23 Mount onto fastening nut 67
and fasten by turning
Y4 Parallel guide 10 Turn guide around and hang it
into the guide rails from below;
tighten clamping handle 35
Y5 Allen key 21 Insert into holders 68
Allen key 64
Y5 Angle stop 3 Insert into retaining clamp 69
Y6 Auxiliary parallel Insert into retaining brackets
guide 37 30 (short side goes on top; long
side toward the rear)
Carrying the Power Tool
Before transporting the power tool, the following steps must
be carried out:
1 619 929 J53 | (12.5.11)
– Bring the machine into the transport position. (see "Trans-
port Position", page 33)
– Remove all accessories that cannot be mounted firmly to
the power tool.
If possible, place unused saw blades in an enclosed con-
tainer for transport.
– Slide the saw-table extension 14 completely to the rear
and press tensioning lever 15 downward to lock it.
– Wind the mains cable around the cable holder 29.
– For lifting or transport, use the recessed handles 4 or the
carrying handle 13.
When transporting the power tool, use only the trans-
port devices and never use the protective devices.
The power tool should always be carried by two per-
sons in order to avoid back injuries.

Maintenance and Service

Maintenance and Cleaning

Before any work on the machine itself, pull the mains
plug.
If the machine should fail despite the care taken in manufac-
turing and testing procedures, repair should be carried out by
an after-sales service centre for Bosch power tools.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
Cleaning
– For safe and proper working, always keep the power tool
and its ventilation slots clean.
– Remove dust and chips after each working procedure by
blowing out with compressed air or with a brush.
Power Tool Lubrication
Lubricants:
SAE 10/SAE 20 engine oil
– If required, lubricate the power tool at the indicated loca-
tions. (see figure Z)
An authorized Bosch after-sales service agent will carry out
this work quickly and reliably.
Observe all applicable environmental regulations when
disposing of old grease and solvents.
Measures for Noise Reduction
Measures on behalf of the manufacturer:
– Soft starting
– Delivery of the machine with a saw blade developed partic-
ularly for noise reduction
Measures on behalf of the user:
– Low-vibration assembly on a firm working surface
– Use of saw blades with noise-reducing functions
– Regular cleaning of saw blade and power tool
Bosch Power Tools