EINHELL BT-TS 1500 U Originalbetriebsanleitung Seite 23

Anleitung_BT_TS_1500_SPK1:_
6. Assembly
Important! Pull out the power plug before
carrying out any maintenance, resetting or
assembly work on the cutting-off machine!
6.1 Assembling the base frame (Fig. 15/16/17)
Turn the saw upside down and place it on the
floor.
Use the washers (b) and the hex screws (a) to
fasten the 4 legs (29) loosely to the saw.
Now use the hex screws (a), the washers (b)
and the nuts (c) to fasten the longitudinal struts
(31) and the cross-struts (30) loosely to the legs.
Please note: The longer struts have to be used
on the sides.
Finally, tighten all screws and nuts on the base
frame.
Screw the additional legs (A) to the rear legs
(29) so that they point towards the rear of the
machine (Fig. 26).
6.2 Fitting / removing the saw blade guard (Fig. 3)
Mount the saw blade guard (2) on the splitter (5)
so that the screw fits through the hole (18) in the
splitter.
Do not tighten the screw (15) too far – the blade
guard must be able to move freely.
Fasten the extractor hose (13) to the extractor
adapter (16) and to the extractor socket of the
blade guard (2).
A suitable extractor system has to be connected
to the outlet of the extractor adapter (16).
To remove the saw blade guard, proceed in
reverse order.
Important!
The guard hood (2) must always be lowered
over the workpiece before you begin to cut.
6.3. Setting the splitter (Fig. 3/5/6/7)
Important! Pull out the power plug.
Set the blade (4) to max. cutting depth, move to
0° position and lock in place.
Remove the saw blade guard (see 6.2).
Take out the table insert (6) (see 6.4).
Slacken the fixing screw (19).
6.3.1. Setting for maximum cuts (Fig. 5/6/7)
Push up the splitter (5) until the gap between the
saw table (1) and the upper edge of the splitter
(5) equals approx. 10 cm.
The distance between the blade (4) and the
splitter (5) should be 3-5 mm.
Retighten the screw (19) and mount the table
insert (6) (Fig. 6).
31.08.2010 8:31 Uhr Seite 23
6.4 Changing the table insert (Figure 6)
To prevent increased likelihood of injury the
table insert should be changed whenever it is
worn or damaged.
Remove the saw blade guard (2).
Remove the 1 countersunk head screws (17).
Take out the worn table insert (6).
To fit the replacement table insert, proceed in
reverse order.
6.5 Fitting/replacing the blade (Fig. 4)
Important! Pull out the power plug first.
Remove the table insert by undoing the two
countersunk head screws (see 6.4).
Undo the nut with a size 24 wrench on the nut
itself and a second fork wrench (size 13) on the
motor shaft to apply counter-pressure.
Important! Turn the nut in the direction of
rotation of the saw blade.
Take off the outer flange and pull the old saw
blade off the inner flange by dropping the blade
at an angle.
Clean the blade flange thoroughly before fitting
the new blade.
Mount and fasten the new saw blade in reverse
order.
Important! Note the running direction. The
cutting angle of the teeth must point in
running direction, i.e. forwards (see the
arrow on the blade guard).
Refit and set the splitter (5) and the saw guard
(2) (see 6.2., 6.3.)
Check to make sure that all safety devices are
properly mounted and in good working condition
before you begin working with the saw again.
6.6 Assembling the table width extension (Fig.
25-26)
Use the screws (a), nuts (b) and washers (c) to
fasten the table width extensions (33) loosely to
the saw table (1) (Fig. 25).
Screw the supports (32) loosely onto the saw
housing and onto the table width extensions (33)
(Fig. 26).
Align the table width extensions (33) level with
the saw table.
Finally, tighten all screws (a).
GB
23