Epson PP 405 Benutzerhandbuch Seite 106

Appendix F EPSON LQ 2550 and ESC/P2 Quick Reference
Table B-5: Horizontal Form Handling and Printing Modes
Escape Sequence
ESC SO
ESC SI
ESC SP P1
ESC ! P1
ESC $ P1 P2
ESC \ P1 P2
ESC % P1
Function
Select Double Width for One Line
Select Condensed
10 cpi -> 17 cpi
12 cpi -> 20 cpi
15 cpi -> 15 cpi (unchanged)
proportional -> proportional cond.
Select Intercharacter Space
Unit 1/120" for DRAFT (P1 = 0/0...7/F)
Unit 1/180" for NLQ/LQ (P1 = 0/0...7/F)
Select Multiple Print Mode
P1 selects:
Bit0 = 0 : 10 cpi (Pica)
Bit0 = 1 : 12 cpi (Elite)
Bit1 = 1 : proportional
Bit2 = 1 : Condensed
Bit3 = 1 : Emphasized
Bit4 = 1 : Double Strike
Bit5 = 1 : Double Width
Bit6 = 1 : Italics
Bit7 = 1 : Underline
Set Absolute Horizontal Position
1
(P1 + P2 * 256) * / " (P1 = 0/0...F/F)
60
(P2 = 0/0...0/3)
Set Relative Horizontal Position
1
Draft: (P1 + P2 * 256) * / "
120
(P1 = 0/0...F/F) (P2 = 0/0...0/6)
1
NLQ/LQ: (P1 + P2 * 256) * / "
180
(P1 = 0/0...F/F) (P2 = 0/0...0/9)
Select Standard / User Defined Character
Set
P1 = 0/0 : Standard Character Set
P1 = 0/1 : User Defined Character Set
F-7
Appendix F EPSON LQ 2550 and ESC/P2 Quick Reference
Table B-5 (Cont.): Horizontal Form Handling and Printing Modes
Escape Sequence
ESC & NUL P1 P2 P3 P4 P5 v1 .. vn
- This Command defines one or more characters in a RAM character
Notes:
table.
- All User Defined Characters are erased when the printer is switched
off.
- Set the Interface Buffer to 1k or 8K (max 50 defined char in LQ, 128 in
draft), or use a RAM card for up to 128 User Defined Characters in LQ.
- Set maximum every second dot to "1" in a horizontal line !
- User Defined Characters can be defined in four different print modes:
Normal Size with Draft:
Normal Size with LQ / proport.:
Sub-/ Superscript with Draft:
Sub-/ Superscript with LQ / proport.:
- The characters can only be activated in the same mode as defined.
- The character layout is coded in three bytes (24 bit vertical) or two
bytes (16 bit vertical) per column, top to bottom.
- To print the character change to the User Defined Character Set with
ESC % .
vertical box, normal size with draft at code table position "41"
Examlpe:
(P3=8, P4=5, P5=8)
hex: 1B 26 00 41 41 08 05 08 FF FF FF 00 00 00 80 00 01 00 00 00 FF FF FF
F-8
Function
Define User Defined Characters
P1 = first code table position
(P1 = 0/0...P2)
P2 = last code table position
(P2 = P1...7/F)
P3 = front space (P3 = 0/0...5/0)
P4 = body length Draft: (P4 = 0/0...0/F)
LQ: (P4 = 0/0...2/5)
P5 = rear space (P5 = 0/0...5/0)
v1 .. vn = binary data in hex
(vn = 0/0...F/F)
resolution (vertical x horizontal)
24 x 15
24 x 37
16 x 15
16 x 37