Flow Volume Table; Maintenance And Cleaning Of Airless Hard-Metal Tips; Spray Gun Accessories - WAGNER EP 3000 Betriebsanleitung

Flow volume table

Tip
ø mm ø inch (")
0.18 0.007
0.23 0.009
0.28 0.011
0.33 0.013
0.38 0.015
0.46 0.018
0.53 0.021
0.66 0.026
0.79 0.031
0.91 0.036
1.10 0.043
1.30 0.052
*Flow volume refers to water.
Maintenance and cleaning of Airless spray tips
Standard tips
If a different tip type has been fitted, then clean it according to manufacturer's instructions.
The tip has a bore processed with the greatest precision. Careful handling is necessary to achieve long durability.
Do not forget the fact that the hard-metal insert is brittle! Never throw the tip or handle with sharp metal objects.
The following points must be observed to keep the tip clean and ready for use:
1. Open the relief valve (valve position k).
2. Switch off unit.
3. Dismount the tip from the spray gun.
4. Place tip in an appropriate cleaning agent until all coating material residue is dissolved.
5. If there is pressure air, blow out tip.
6. Remove any residue by means of a sharp wooden rod (toothpick).
7. Check the tip with the help of a magnifying glass and, if necessary, repeat points 4 to 6.

Spray gun accessories

Flat jet adjusting tip
up to 250 bar (25 MPa)
Bore
Tip marking mm
15 0.13 - 0.46
20 0.18 - 0.48
28 0.28 - 0.66
41 0.43 - 0.88
49 0.53 - 1.37
Tip extension
with
slewable knee joint
(without tip)
Length 100 cm
Length 200 cm
Length 300 cm
Spray angle
10-20-50°
10-20-40-50-60°
10-20-40-50-60-80°
10-20-40-50-60-80°
10-20-40-50-60-80°
20-40-50-60-80°
20-40-50-60-80°
20-40-50-60-80°
40-50-60-80°
40-50-60-80°
50-60-80°
50°
Spray width at about 30 cm
removal of spray object
Pressure 100 bar (10 MPa)
5 - 35 cm Paints
5 - 50 cm Paints, fillers
8 - 55 cm Paints, dispersions
10 - 60 cm Rust protection
paints - dispersions
10 - 40 cm Large-area coats
Order no. 0096 015
Order no. 0096 016
Order no. 0096 017
g
Flow volume in l/min*
at 70 bars
0.16
0.23
0.30
0.45
0.61
0.95
1.25
1.90
2.84
3.79
5.69
7.60
Flat jet
Use adjusting tip
Order no.
0999 057
0999 053
0999 054
0999 055
0999 056
Tip extension
Length 15 cm
Length 30 cm
Length 45 cm
Length 60 cm
37
at 100 bars at 150 bars
0.19 0.26
0.26 0.30
0.38 0.47
0.57 0.69
0.72 0.91
1.14 1.40
1.56 1.90
2.32 2.80
3.50 4.20
4.56 5.50
6.84 8.30
9.12 11.10
Contact protection
for the flat jet adjustment tip
Order no. 0097 294
Order no. 0999 320
Order no. 0999 321
Order no. 0999 322
Order no. 0999 323