Inhaltsverzeichnis
Werbung
GB
Faulty and/or discarded electrical or electronic apparatus have to be collected
at the appropriate recycling locations.
D
Specific safety instructions
NL
•
If you are working with the sanding machine, wear always ear protectors and dust
mask.
•
The sanding machine is not suitable for wet sanding.
F
•
Check if the switch is not in position "ON", before you connect the mains plug to the
mains voltage.
•
Keep the mains lead always away from moving parts of the tools.
E
•
Use safety glasses, especially when you sand above your head.
•
Do not bring pressure to your machine, this will only delay the sanding.
P
The dust that is produced while working can be detrimental to health,
inflammable or explosive. Suitable safety measures are required. Always wear
suitable safety equipment, for example a dust mask, and use the dust bag.
I
Immediately switch off the machine when:
•
Excessive sparking of the carbon brushes and verticiliosis in the collector.
S
•
Interruption of the mains plug, mains lead or mains lead damage.
•
Defect switch
FIN
•
Smoke or stench of scorched isolation
Electrical safety
N
When using electric machines always observe the safety regulations applicable in your
country to reduce the risk of fire, electric shock and personal injury. Read the following
safety instructions and also the enclosed safety instructions.
DK
Always check that the power supply corresponds to the voltage on the rating
plate.
Class ll machine. Your machine is double insulated; therefore no earthwire is
required.
Replacing cables or plugs
Immediately throw away old cables or plugs when they have been replaced by new ones.
It is dangerous to insert the plug of a loose cable in the wall outlet.
Using extension cables
Only use an approved extension cable suitable for the power input of the machine. The
minimum conductor size is 1.5 mm
completely.
6
2
. When using a cable reel always unwind the reel
• Slibemaskinen bliver for
varm
• Støvet suges ikke op
Reparationer må udelukkende udføres af en autoriseret installatør eller et
autoriseret serviceværksted.
Rengøring
Rengør maskinhuset regelmæssigt med en blød klud, fortrinsvist efter hver anvendelse. Hold
blæserristen fri for støv og snavs. Fjern fastsiddende snavs med en blød klud fugtet med
søbevand. Brug ikke opløsningsmidler, som f.eks. benzin, alkohol, ammoniak, osv. Disse
midler kan beskadige plastikdelene.
Smøring
Maskinen behøver ingen ekstra smøring.
Fejl
Skulle en fejl opstå, f.eks. pga. slidtage af en enhed, kontakt venligst serviceadressen på
garantibeviset. På bagsiden af denne manual finder du en tegning med alle dele, der kan bestilles.
Miljø
For at undgå transportbeskadigelse leveres maskinen i en solid emballage. Emballagen er så
vidt muligt lavet af genbrugsmateriale. Genbrug derfor emballagen.
Defekte og/eller kasserede elektriske eller elektroniske maskiner skal afleveres på
en genbrugsplads.
Garanti
Læs det separat vedlagte garantikort for garantibetingelserne.
Ferm
Ferm
• Slibemaskinen belastes
• Brug maskinen til det,
for meget.
den er beregnet til.
• Motoren er defekt.
Indlever slibemaskinen til
reparation hos Deres
forhandler.
• Dette kan eventuelt
• Rens åbningen til
skyldes, at
udsugning af støv.
støvudsugningen er
tilstoppet.
GB
D
NL
F
E
P
I
S
FIN
N
DK
79
Werbung
Inhaltsverzeichnis
