Nice Neomat T series Installierungs-Und Gebrauchsanleitungen Und Hinweise Seite 7

position by pressing the ▲ and ▼ buttons of the transmitter together.
Follow the procedure shown in table A4 to memorise the intermediate position:
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Table "A4" - Programming of the intermediate position "I"
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
01. Using buttons ▲ ■ ▼ of a remote control, move the
awning into the "I" position to be memorised.
02. Press and hold down button ■ until you hear a beep
5s...
(after about 5 seconds).
03. Release and press again button ■ for another 5 seconds
5s...
until 4 rapid beeps are heard.
04. Press buttons ▼ and ▲ together until 3 beeps are heard,
indicating that the position has been memorised.
4.3.2 - Deactivation or reactivation of Torque Reduction on closing (RDC)
Torque reduction is a function that reduces the traction torque by approx. 50% shortly
before complete closure of the awning against the casing, to avoid excessive tensioning of
the fabric. This function is activated automatically after programming positions 0 and 1
(programming is always at maximum force) but can be deactivated (or re-activated) if
required.
Note - automatic activation of the RDC function does not occur if position programming is
performed using programmers TTP, TTI and O-ViewTT; in these cases the function can be
activated manually as required.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Table "A5" - Deactivation or reactivation of Torque Reduction (RDC)
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
01. Press and hold down button ■ of a previously memorized
5s...
transmitter until you hear a beep (after about 5 seconds).
02. Release and press again button ■ for another 5 seconds
5s...
until 4 rapid beeps are heard.
03. Press ■ until the signal beeps are emitted: 3 Beeps indi-
(...)
cate RDC active (closure at reduced torque); 5 Beeps
indicate RDC not active (closure at maximum torque).
4.3.3 - Deleting positions
To modify the previously memorised positions, they must firstly be cancelled and then the
new positions programmed again.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Table "A6" - Cancellation of the intermediate position "I"
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
01. Press and hold down button ■ of a previously memorized
5s...
transmitter until you hear a beep (after about 5 seconds).
02. Release and press again button ■ for another 5 seconds
5s...
until 4 rapid beeps are heard.
03. Press buttons ▼ and ▲ together until 5 beeps are heard, in -
di cating that the intermediate position has been cancelled.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Table "A7" - Cancellation of positions "0" and "1"
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
01. Press and hold down button ■ of a previously memorized
5s...
transmitter until you hear a beep (after about 5 seconds).
02. Release and press again button ■ for another 5 seconds
5s...
until 4 rapid beeps are heard.
03. Press button ▼ until 5 beeps signal that positions "0"
and "1" have been cancelled.
WARNING: After deleting positions "0" and "1" the awning moves in hold-to-run mode
and the new positions need to be memorised.
Note: the intermediate positions "I" and the RDC function that are programmed are not
cancelled. If you wish to cancel everything (including the codes of the transmitters), refer to
table "A14".
4.3.4 - Programming of the "wind" weather sensor level
If a "VOLO" or "VOLO S" wind sensor is connected to the "sensors" input, the wind protec-
tion is activated that automatically retracts the awning when the wind exceeds the pro-
grammed level. If the level is exceeded for more than 3 seconds, a command that is the
same as the ▲ button is activated and any other movement is blocked until the wind level
returns below the programmed level for more than 1 minute. There is a choice of 5 differ-
ent activation levels: 1=5Km/h, 2=10Km/h, 3=15Km/h, 4=30Km/h and 5=45Km/h. (the
level is factory set at No.3).
If using the sensor "VOLO ST" or radio sensors Volo S Radio and Nemo, the wind trip
thresholds are programmed directly on the sensor (see relative instructions).
To modified the programmed level:
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Table "A9" - Changing the activation level of the "wind" protection
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
01. Press and hold down button ■ of a previously memo-
5s...
rized transmitter until you hear a beep (after about 5 sec-
onds) then release it.
02. Slowly press button ▲ the same number of times (1, 2,
x 1 = 5 Km/h
x 2 = 10 Km/h 3, 4 or 5) as the desired level.
x 3 = 15 Km/h
x 4 = 30 Km/h
x 5 = 45 Km/h
English – 5