Nice Neomat T series Installierungs-Und Gebrauchsanleitungen Und Hinweise Seite 11

No. Command
1 Step-by-Step (up-stop-down-stop...),
2 Up-Stop (up-stop-up-stop...)
3 Down-Stop (down-stop-down-stop...)
4 Stop
5.2.3 - Example of Mode I and Mode II combined memorization
Group commands can be created taking opportune advantage of the Mode I and Mode II
memorizations as shown in the fig. F.
• The T1 transmitter (Ergo1) memorized in Mode I on A1 and A2 simultaneously com-
mands the Up, Stop or Down of both A1 and A2.
• The T2 transmitter (Plano1) memorized in Mode I on A3 only, commands the Up, Stop or
Down of A3 only.
• The T3 transmitter (Planotime) memorized in Mode 1 on A4 only, commands the Up,
Stop or Down of A4 only.
• The T4 transmitter (WM001C) memorized in Mode II (Step-by-Step) commands A4 only.
• The T5 transmitter (WM003G) memorized in Mode I to command A1 and A2 with group
1, A3 with group 2 and A4 with group 3; commands the Up, Stop or Down of A1 and
A2, A3 or A4.
• The T6 transmitter (Flo4R) memorized in Mode II on A4 (buttons 1 and 3) on A5 (button
2) and on A6 (button 4), commands the Up and Down of A4, or the opening of the
garage door A5 or the opening of the automatic gate A6.
WARNING:
• Some functions (positions, levels...) cannot be programmed with the transmitter mem-
orized in Mode II as different buttons need to be pushed in this phase, such as button ■
and button ▲ for example.
• The "multiple group" commands cannot be used with a transmitter memorized in Mode II.
When one or more transmitters have already been memorized, others may be memorized
in Mode II as shown in table A16.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Table "A16" - Memorizing additional transmitters in Mode II
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
01. Press and hold down the button to be memorized of the
new 5s.
new transmitter (for approx. 5 seconds) until you hear a
beep; then release it.
02. Within 5 seconds push and hold the button of an old and
old 5s.
already memorized transmitter (approx. 5 seconds) until
2 beeps are heard; then release the button.
03. Within 5 seconds start to push the same button of the old
new 1- 4
transmitter the same number of times equal to the re quired
command: 1="Step-by-Step" 2="Up" 3="Down" 4="Stop".
04. After about 3 seconds the same number of beeps as the
3s. 1- 4
selected command are heard.
05. Within 2 seconds push the same button of the new
new
transmitter.
06. Release the button when you hear the first of the 3
beeps confirming memorization.
If at point 5 the same number of beeps equal to the selected command are not heard, sim-
ply do not push any more buttons and wait a few seconds for the programming to finish
without memorizing.
Note: If the memory is full (14 transmitters), 6 beeps will indicate that the transmitter can-
not be memorized.
A new transmitter can easily be memorized with the same characteristics as that of the old
one by following the procedure in table A17. The "new" transmitter will inherit the charac-
teristics of the old one, i.e. if the old transmitter was memorized in Mode 1, the new one
will also function in Mode 1, if the old transmitter was memorized in Mode II then the but-
ton of the new transmitter will be associated to the same command as that of the old one.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Table "A17" - Memorizing other transmitters
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
01. Press and hold down the button to be memorized of the
new
> 3s.
new transmitter (for approx. 3 seconds) then release it.
02. Press and hold down the button to be memorized of the
old > 3s.
old transmitter (for approx. 3 seconds) then release it.
03. Press and hold down the button to be memorized of the
new
> 3s.
new transmitter (for approx. 3 seconds) then release it.
04. Press and hold down the button to be memorized of the
old > 3s.
old transmitter (for approx. 3 seconds) then release it.
05. The memorization of the new transmitter is confirmed
with 3 beeps.
Note: If the memory is full (14 transmitters), 6 beeps will indicate that the transmitter can-
not be memorized.
English – 9