Technical Data; Before Starting The Equipment - EINHELL BT-LS 810 D Bedienungsanleitung

Anleitung_RBK_4645_SPK1:_
The machine is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the
manufacturer will be liable for any damage or injuries
of any kind caused as a result of this.
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

4. Technical data

Engine displacement
Maximum engine capacity
Bar length
Cutter rail length
Chain pitch
Chain thickness
Idling speed
Maximum speed with cutting equipment
Tank capacity
Oil tank capacity
Anti-vibration function
Chain wheel teeth
Chain brake
Clutch
Automatic chain lubrication
Low-kickback chain
Net weight without chain and chain bar
Net weight (dry)
Fuel consumption (specific)
L sound pressure level
pA
L sound power level
WA
Vibration a (front handle)
hv
Uncertainty (k) (front handle)
Vibration a (rear handle)
hv
Uncertainty (k) (rear handle)
Chain type
Carlton (K2L-BL, 72X), Oregon (21BP, 72X)
Bar type
Spark plug
14.12.2009 15:18 Uhr Seite 21

5. Before starting the equipment

Important: Do not start the engine until the saw
is fully assembled.
Important: Wear protective gloves at all times
when handling the chain.
5.1 Fit the chain bar
To ensure that the bar and the chain are supplied
with oil, USE ONLY THE ORIGINAL BAR. The oiling
hole (Fig. 2/Item A) must be kept clear of dirt and any
build-up of residue.
1. Make sure the Chain brake lever is pulled back
into the DISENGAGED position (Fig. 3A).
46 cm 3
2. Remove the two bar fastening nuts (B). Remove
the cover (Fig. 3B).
2 kW
3. Using a screwdriver, run the adjustment screw
43 cm
(D) COUNTERCLOCKWISE until the TANG (E)
18" (45 cm)
(projecting prong) is to the end of its travel toward
(0.325"), 8.255 mm
the clutch drum and sprocket (Fig. 3C).
4. Fit the open end of the chain bar over the die bar
(0.058") 1.47 mm
pins (F) (Fig. 3D).
3600 rpm
10000 rpm
5.2 To install saw chain
550 ml
1. Spread chain out in a loop with cutting edges (A)
pointing CLOCKWISE around loop (Fig. 4A).
260 ml
2. Slip the chain around the sprocket (B) behind the
Yes
clutch (C). Make sure the links fit between the
7 x 8.255 mm
sprocket teeth (Fig. 4B).
Yes
3. Guide the drive links into the groove (D) and
around the end of the bar (Fig. 4B).
Yes
Yes
NOTE: The saw chain may droop slightly on the lower
Yes
part of bar. This is normal.
5.5 kg
4. Pull the chain bar forward until the chain is closely
7 kg
seated. Make sure that all the drive links are in
560 g / kWh
the groove of the bar.
104 dB(A)
5. Fit the clutch cover and fasten it with 2 screws.
116 dB(A)
Make sure that the pivot (Fig. 3C/Item E) fits into
the chain bar (Fig. 3D/Item G). The chain must
max. 5.99 m/s 2
not slip off the bar when you do this. Tighten the
max. 1.5 m/s
2
two nuts by hand and then follow the instructions
max. 7.54 m/s 2
for adjusting the tension in ADJUSTING THE
max. 1.5 m/s 2
CHAIN TENSION.
5.3 Saw chain tension adjustment
Proper tension of saw chain is extremely important
POH18-58SH
and must be checked before starting, as well as
LDL7T
during any cutting operation.
Taking the time to make needed adjustments to the
saw chain will result in improved cutting performance
and prolonged chain life.
GB
21