Grundig GDV 100 D Servicehandbuch Seite 71

GDV 100 D
– "Unexpected response from Basic Engine"
Error code: DD_ERR_BEDISCMOTOROFF_UNEXPECTED_RESPONSE
– "Communication time-out error"
Error code: DD_ERR_BEDISCMOTOROFF_COMMUNICATION_TIMEOUT
– "Basic Engine returned error number 0xXX"
Error code: DD_ERR_BEDISCMOTOROFF_CMD_EXECUTION
The error numbers 0xXX are listed in [BE] on page 3-32.
Send the spindle_motor_off command to the Basic Engine to switch
the spindle motor off.
Refer also to Service Test Levels PapS2bEcho and BeDiscmotorOn.
60a (BeRadialOn)
Send the radial_on command to the Basic Engine.
Check if it is possible to close the radial loop.
Message:
– "Parity error from Basic Engine to Serial"
Error code: DD_ERR_BERADIALON_PARITY_B2S
– "Unexpected response from Basic Engine"
Error code: DD_ERR_BERADIALON_UNEXPECTED_RESPONSE
– "Communication time-out error"
Error code: DD_ERR_BERADIALON_COMMUNICATION_TIMEOUT
– "Basic Engine returned error number
Error code: DD_ERR_BERADIALON_CMD_EXECUTION
– "Radial loop could not be closed"
Error code: DD_ERR_BERADIALON_COMMAND_COMPLETE
The error numbers 0xXX are listed in [BE] on page 3-32.
Send the radial_on command to the Basic Engine to close the radial
loop. The radial loop can only be closed if a DVD-disc is in the tray. If
no disc is in the tray, the actuator keeps ramping because the Basic
Engine tries to put the laser into focus.
Refer also to Service Test Level PapS2bEcho.
60b (BeRadialOff)
Open the radial loop.
An operator must check if the commands mentioned in the description
are executed successfully.
Message:
– "Parity error from Basic Engine to Serial"
Error code: DD_ERR_BERADIALOFF_PARITY_B2S
– "Parity error from Basic Engine to Serial"
Error code: DD_ERR_BERADIALOFF_UNEXPECTED_RESPONSE
– "Communication time-out error"
Error code: DD_ERR_BERADIALOFF_COMMUNICATION_TIMEOUT
– "Basic Engine returned error number 0xXX"
Error code: DD_ERR_BERADIALOFF_CMD_EXECUTION
The error numbers 0xXX are listed in [BE] on page 3-32.
Send command radial_off to the Basic Engine, to open the closed
radial loop; send command focus_off to stop the ramping of the
actuator (laser can't be put in focus with BeRadialOn) or in case the
laser is in focus, the focus loop will be switched off; send command
laser_off to switch the laser off; send command spindle_motor_off to
switch the spindle motor off.
Refer also to Service Test Levels PapS2bEcho and BeRadialOn.
61a (BeSledgeIn)
Move the sledge fully inwards
An operator must check if the sledge moves fully inwards.
Message:
– "Parity error from Basic Engine to Serial"
Error code: DD_ERR_BESLEDGEIN_PARITY_B2S
– "Unexpected response from Basic Engine"
Error code: DD_ERR_BESLEDGEIN_UNEXPECTED_RESPONSE
– "Communication time-out error"
Error code: DD_ERR_BESLEDGEIN_COMMUNICATION_TIMEOUT
– "Basic Engine returned error number XX"
Error code: DD_ERR_BESLEDGEIN_CMD_EXECUTION
The error numbers XX and 0xYY are listed in [BE] on page 3-32.
Refer also to Service Test Level PapS2bEcho.
61b (BeSledgeOut)
Move the sledge fully outwards
An operator must check if the sledge moves fully outwards.
GRUNDIG Service
0xXX"
Message:
– "Parity error from Basic Engine to Serial"
Error code: DD_ERR_BESLEDGEOUT_PARITY_B2S
– "Unexpected response from Basic Engine"
Error code: DD_ERR_BESLEDGEOUT_UNEXPECTED_RESPONSE
– "Communication time-out error"
Error code: DD_ERR_BESLEDGEOUT_COMMUNICATION_TIMEOUT
– "Basic Engine returned error number XX"
Error code: DD_ERR_BESLEDGEOUT_CMD_EXECUTION
The error numbers XX and 0xYY are listed in [BE] on page 3-32.
Send move_sledge command with a positive number of steps (fixed
number) to the Basic Engine to move the sledge fully outwards.
Refer also to Service Test Levels PapS2bEcho and BeSledgeIn.
62a (BeGroovesIn)
Move the laser spot to the inside position of the disc.
Message:
– "Parity error from Basic Engine to Serial"
Error code: DD_ERR_BEGROOVESIN_PARITY_B2S
– "Unexpected response from Basic Engine"
Error code: DD_ERR_BEGROOVESIN_UNEXPECTED_RESPONSE
– "Communication time-out error"
Error code: DD_ERR_BEGROOVESIN_COMMUNICATION_TIMEOUT
– "Basic Engine returned error number 0xXX"
Error code: DD_ERR_BEGROOVESIN_CMD_EXECUTION
– "Sledge could not be moved to home position"
Error code: DD_ERR_BEGROOVESIN_SLEDGE_ERROR
– "Focus loop could not be closed"
Error code: DD_ERR_BEGROOVESIN_FOCUS_ERROR
– "Motor not on speed within time-out"
Error code: DD_ERR_BEGROOVESIN_MOTOR_ERROR
– "Radial loop could not be closed"
Error code: DD_ERR_BEGROOVESIN_RADIAL_ERROR
– "PLL could not lock in accessing or tracking state"
Error code: DD_ERR_BEGROOVESIN_PLL_LOCK_ERROR
– "Subcode or sector information could not be read"
Error code: DD_ERR_BEGROOVESIN_SUBCODE_HEADER_TIMEOUT
– "Requested subcode item could not be found"
Error code: DD_ERR_BEGROOVESIN_SUBCODE_NOT_FOUND
– "TOC could not be read in time"
Error code: DD_ERR_BEGROOVESIN_READ_TOC_ERROR
– "Seek could not be performed"
Error code: DD_ERR_BEGROOVESIN_JUMP_ERROR
The error numbers 0xXX are listed in [BE] on page 3-32.
Send the read_toc command to the Basic Engine to move the laser
spot to the inside position of the disc.
Refer also to Service Test Level PapS2bEcho.
62b (BeGroovesMid)
Move the laser spot to the middle position of the disc.
Message:
– "Parity error from Basic Engine to Serial"
Error code: DD_ERR_BEGROOVESMID_PARITY_B2S
– "Unexpected response from Basic Engine"
Error code: DD_ERR_BEGROOVESMID_UNEXPECTED_RESPONSE
– "Communication time-out error"
Error code: DD_ERR_BEGROOVESMID_COMMUNICATION_TIMEOUT
– "Basic Engine returned error number 0xXX"
Error code: DD_ERR_BEGROOVESMID_CMD_EXECUTION
– "Sledge could not be moved to home position"
Error code: DD_ERR_BEGROOVESMID_SLEDGE_ERROR
– "Focus loop could not be closed"
Error code: DD_ERR_BEGROOVESMID_FOCUS_ERROR
– "Motor not on speed within time-out"
Error code: DD_ERR_BEGROOVESMID_MOTOR_ERROR
– "Radial loop could not be closed"
Error code: DD_ERR_BEGROOVESMID_RADIAL_ERROR
Service Test Programme
3 - 29