Herunterladen Inhalt Inhalt Diese Seite drucken
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 18
GB
1

INSTALLATION TIPS

Installing the car seat with a 3-point safety
belt
The STORM can only be used with automatic
3-point safety belt. (Fig. 1)
The STORM can be fitted in a forward-facing
position in the rear seats of the car by using
the existing seat belts. However, on some
seats, if the installation is not properly fitted,
we suggest try another seat in your car.
Five positions of the car seat
The
STORM can
positions (Fig. 2):
Pull the positioning handle under the front
of the seat forwards or backwards (feel the
spring underneath), release the handle on
your required position while hearing a distinct
click.
2
INSTALLATION
Installing method for Group I (9-18 kg)
a) Place the STORM in the sleeping position 3
or 4. (Fig. 3)
b) Remove the installation shaft by pulling the
moveable part of the lock from the STORM.
(Fig. 4-A)
c) Pull and hold the shell forward, the thread
the seat belt between the shell and the base,
fasten the seat belt with the seat buckle, and
ensure the belt is not twisted. (Fig. 5)
* Make sure the shoulder belt go from top of
the seat and through the lock-off device (Fig.
5-A) and the lap belt go horizontally over lap
belt hook (Fig. 5-B) and joint with the shoulder
belt and buckle up the seat. (Fig. 5-C)
d) Return the shell to its original position, and
thread the installation shaft into the hole and
lock the device by pushing the moveable part
on the other side until hear a distinct click.
(Fig. 4-B)
e) Adjust the shell to your child's most com-
fortable position.
3
Installing method for Group II (15-25 kg)
The installation method is for child within
16
IM 1442,01 STORM BE COOL ins.indd 16
be
used
in
Five
Group II (15-25 Kg). Removing the harness sys-
tem first, includind the belt pads, buckle and
crotch strap, then install the shoulder and lap
belt by threading the vehicle's lap and shoul-
der belt through the hook (Fig. 6-A) on the top
of shell and over the belt guide. (Fig. 6-7)
4
Placing your child in the STORM
a) Loosen the shoulder belts by pressing the
release button and pull the shoulder belts to-
wards you.
Important: Do not pull on the belt pads when
doing so. (Fig. 8-9)
b) Press the red button to open the buckle.
(Fig. 10)
c) Part the belts over the sides of the shell.
(Fig. 11)
d) Position your child into the shell and make
sure that there are no toys or other hard ob-
jects in the shell. (Fig. 12)
e) Match buckle tongue sections together and
insert them into the buckle. (Fig. 13)
f) Make sure the shoulder belts fit your child
snugly by pulling the adjuster belt. (Fig. 14)
Note! When you have done the installation,
check it by trying to move it, it shoudn't
move than an inch side along the belt path,
if it does, tighten the straps or try installing
it again. The belts should never be twisted.
If you are unable to click the buckle sections
into the buckle, unlock the buckle by pressing
the red button and try again.
5
Adjusting the height of the shoulder belts
a) The correct belt height of the shoulder belts
is attained when the belt disappears into the
shell slightly above the shoulder of the child.
Ensure that the shoulder belts fit comfortably
over the child's shoulder. (Fig. 15)
b) Loosen the shoulder belts by pressing the
release button of the adjuster and pulling the
shoulder belts towards you as far as possible.
Important: Do not pull the belt pads when do-
ing so. (Fig. 9)
c) Place the shell of the seat in the sleeping
position.
d) Remove the shoulder belts from the yoke.
13/03/13 11:53

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis