General Information; Installation - be cool JET i-fix Gebrauchsanweisung

GB
1 INTRODUCTION
The JET i-fix car seat can be installed in most
vehicles equipped with Isofix (anchors), al-
ways in combination with the seat belts of the
car. Correct compatibility can be verified by
checking the usage list.
Important: JET l-FIX is approved as a semi-
universal seat. This means that it must be
used only in the vehicles indicated in the us-
age list.
Product information
This car seat has been designed and tested to
comply with the latest European standards for
Group 2 & 3 car seats.
This car seat has been designed for children
weighing between 15 and 36 kg, and aged be-
tween 4 and 11 years approximately.
All ages given are approximate, because all
children grow at different rates the weights
given are the main safety issue.
To improve your child's safety, the JET i-fix
seat is fitted with:
JET i-fix (anchors) for Isofix (anchors).
3 point seat belt in the car.
A headrest with 4 height positions to maintain
protection as the child grows.
Higher sides provide greater protection
against side impact.

GENERAL INFORMATION

In order to protect your child adequately and
make sure that they are comfortable and se-
cure in the car, you must follow these instruc-
tions:
Your JET i-fix seat has been designed to be
installed on the rear or front seat of the car,
provided that you have three-point seat belts
and that the front AIR BAG is not connected.
Even so, we recommend that whenever pos-
sible, you install it on the rear seat, as this will
ensure maximum safety.
It is only suitable for cars fitted with auto-
matic, three-point
in accordance with ECE-16 standard or other
equivalent standards.(F3)
Do NOT use with a two-point anchoring seat
belt.
This is very dangerous should you brake sud-
denly or in the event of an accident.(F4)
In some cars, the seat belt clasp might be in
very high position and may come into contact
with the edge of the booster seat, making this
position unsafe. In this case, try moving the
vehicle seats forwards or install it on another
14 seat. If you have any doubts, contact your lo-
cal distributor or retailer.
- ifi x
seat belts, approved
Not all safety systems are exactly the same, so
we commend that you try the JET i-fix in the
car in which you are going to install it.
It is very important not to use second-hand
products, as Be Cool can only guarantee the
complete safety for items used by initial buy-
er.
Be Cool recommends that you replace your
JET i-fix seat with a new one when it has been
subjected to violent twisting following an ac-
cident.
Ensure that all the belts are in their correct
positions and correctly adjusted to the child.
Make sure that no belt is coiled up. Make the
child understand that under no circumstances
should they touch the belts or fastenings.
The JET i-fix seat has been designed to be
used in the car, so it must not be used any-
where else.
For more information on how to use and in-
stall the JET i-fix, please contact your local
distributer or retailer.

INSTALLATION

Installation of the car seat - Suitable weight
from 15 to 36 kg
Fasten the JET i-fix to the Isofix anchors in
your car.
Isofix anchors have been developed to ensure
secure and easy fastening of child restraint
systems in the car. Not all cars have these
anchors, although they are becoming more
standard in newer models. Consult the at-
tached list of cars in which it has been checked
that the seat can be installed correctly.
1. If your vehicle is equipped with Isofix an-
chors, these can be used as additional fasten-
ers, in order to obtain a more stable installa-
tion.
Some cars are not fitted with plastic parts
to guide the connectors
rect position, corresponding with the anchor
points on the vehicle seat. In this case you can
use the plastic guides provided with the JET
i-fix seat.
(These guides for the Isofix connectors must
be positioned as shown in F5)
Warning: If the seats of your car are equipped
with Isofix anchors, you can install the JET i-fix
seat using the JET i-fix anchors, but ALWAYS
into their cor-