Midi Data Format; Channel Message; System Exclusive Message - Yamaha DTXPRESS II Bedienungsanleitung

MIDI Data Format

1. Channel Message

When the [3-2. Channel 10 Propgram Change/Channel Event Receive] (P. 31)
in the utility mode is set to "10=off", the DTXPRESS II will not receive channel
message for MIDI channel 10.
1.1 Key On Key Off
Sends and receives data.
Receive note range: C-2 to G8
Velocity range: 1 to 127 (note on only)
1.2 Control Change
All control change data for sequencer functions can be received and transmit-
ted. The following lists the tone generator functions and drum trigger functions.
1.2.1 bank select MSB-0
Sends and receives data.
data=0:normal voice
data=127:drum voice
The data will not be processed unless program change data is received.
1.2.2 modulation (No. 1)
Receives only.
1.2.3 foot controller (No. 4)
Sends and receives data.
1.2.3 data entry (No. 6)
Receives only. Used to specify RPN data.
1.2.5 main volume (No. 7)
Sends and receives data.
1.2.6 pan (No. 10)
Sends and receives data.
0 is the far left of a stereo image and 127 is the far right of a stereo image.
1.2.7 expression (No. 11)
Receives only.
1.2.8 hold1 (No. 64)
Receives only.
1.2.9 harmonic content (No. 71)
Receives only.
1.2.10 release time (No. 72)
Receives only.
1.2.11 attack time (No. 73)
Receives only.
1.2.12 brightness (No. 74)
Receives only.
1.2.13 portamento control (No. 84)
Receives only.
1.2.14 effect 1 depth (No. 91)
Receives only. Only effects the reverb send level.
1.2.15 data increment/decrement (No. 100/101)
Receives only.
1.2.16 RPN
00/00 pitch bend sensitivity: Receive only.
00/01 fine tuning: Receive only.
00/02 coarse tuning: Receive only.
7F/7F NULL: Receive only.
1.3 Channel Mode Message
All channel mode messages are received only.
1.3.1 all sound off (No. 120)
Mutes all the sounds currently playing through the specified channel.
50
1.3.2 reset all controllers (No. 121)
Sets the following controller values back to its initial value:
pitch bend, modulation, expression, hold1, portament control,
RPN number
1.3.3 all note off (No. 123)
Turns off all the notes of the specified channel currently on.
They will however, not be muted unless "hold 1" is turned off.
1.3.4 omni off (No. 124)
Executes the same process as "all note off".
1.3.5 omni on (No. 125)
Executes the same process as "all note off".
1.3.6 mono (No. 126)
Executes the same process as "all sound off".
1.3.7 poly (No. 127)
Executes the same process as "all sound off".
1.4 Program Change
When the [3-3. Receive Propgram Change/System Exclusive Messages] (P. 31)
in the utility mode is set to "PC=off", the DTXPRESS II will not receive program
change data.
When the [3-2. Channel 10 Propgram Change/Channel Event Receive] (P. 31)
in the utility mode is set to "10PC=off", the DTXPRESS II will not receive MIDI
channel 10 program change data.
1.5 Pitch Bend
Sends and receives data.
1.6 Channel Aftertouch
Does not sends or receive data.
1.7 Polyphonic Aftertouch
Does not sends or receive data.

2. System Exclusive Message

When the [3-3. Receive Propgram Change/System Exclusive Messages] (P. 31)
in the utility mode is set to "SySex=off", the DTXPRESS II will not receive sys-
tem exclusive messages.
The DTXPRESS II will not receive system exclusive messages that do not match
the device number set in the "DevNo=" of the [3-6. Device Number, Local Con-
trol] (P. 32) in the utility mode.
2.1 Parameter Change
2.1.1 GM system ON
F0 7E 7F 09 01 F7
Sets all the data except the MIDI master tuning data to its initial value.
Sends and receives data.
2.1.2 XG system ON
F0 43 1n 4C 00 00 7E 00 F7
"n" stands for device number.
Executes the same process as GM system ON.
Received only.
2.1.3 identify request
F0 7E 0n 06 01 F7
"n" stands for device number.
After receiving, the identify reply is transmitted.
Received only.
2.1.4 MIDI master volume
F0 7F 7F 04 01 XX mm F7
Ignores "XX". "mm" is the volume.
Received only.