Midi-Datenformat; Data Format; Format Details - Yamaha DM 1000 Bedienungsanleitung

MIDI-Datenformat

1. DATA FORMAT

1.1 CHANNEL MESSAGE
Command
8n NOTE OFF
9n NOTE ON
Bn CONTROL CHANGE
Cn PROGRAM CHANGE
1.2 SYSTEM COMMON MESSAGE
Command
F1 MIDI TIME CODE QUARTER
FRAME
F2 SONG POSITION POINTER
1.3 SYSTEM REALTIME MESSAGE
Command
F8 TIMING CLOCK
FA START
FB CONTINUE
FC STOP
FE ACTIVE SENSING
FF RESET
1.4 EXCLUSIVE MESSAGE
1.4.1 Real Time System Exclusive
Command
F0 7F dd 06 ... F7 MMC
COMMAND
F0 7F dd 07 ... F7 MMC RESPONSE rx
F0 7F dd 01 ... F7 MIDI TIME CODE rx
1.4.2 System Exclusive Message
1.4.2.1 Bulk Dump
Command
F0 43 0n 7E ... F7 BULK DUMP
DATA
F0 43 2n 7E ... F7 BULK DUMP
REQUEST
The following data types of bulk dump are used on the DM1000.
Data name
'm'
'S'
'a'
'R'
'O'
'H'
'G'
'Y'
'Q'
'E'
'J'
'K'
'P'
'C'
'L'
'V'
'U'
'N'
rx/tx function
rx Control the internal effects
rx Control the internal effects
rx/tx Control parameters
rx/tx Switch scene memories
rx/tx function
rx MTC
rx Used when TIME REFERENCE is
MIDI CLOCK.
rx/tx function
rx MIDI clock
rx Start automix (from the beginning)
rx Start automix (from the middle)
rx Stop automix
rx Check MIDI cable connections
rx Clear running status
rx/tx function
tx MMC command
MMC response
MTC full message
rx/tx function
rx/tx BULK DUMP DATA
rx/tx BULK DUMP REQUEST
tx/rx function
tx/rx Scene Memory & Request
(compressed data)
tx/rx Setup Memory & Request
tx/rx Automix data & Request
(compressed data)
tx/rx Input patch library & Request
tx/rx Output patch library & Request
tx/rx Channel library & Request
tx/rx Gate library & Request
tx/rx Compressor library & Request
tx/rx Equalizer library & Request
tx/rx Effect library & Request
tx/rx Bus to Stereo library & Request
tx/rx Surround Monitor library & Request
tx/rx Program change table & Request
tx/rx Control change table & Request
tx/rx User define layer & Request
tx/rx User define key & Request
tx/rx User assignable layer & Request
tx/rx Plug-in Effect Card Data & Request
MIDI-Datenformat
1.4.2.2 PARAMTER CHANGE
Command
F0 43 1n 3E 0C ... F7 RARAMETER
CHANGE
F0 43 3n 3E 0C ... F7 PARAMETER
REQUEST
F0 43 1n 3E 7F ... F7 PARAMETER
CHANGE
F0 43 3n 3E 7F ... F7 PARAMETER
REQUEST
The following data types of parameter change are used by the DM1000.
Type (HEX)
1 (01)
2 (02)
3 (03)
4 (04)
15 (0F)
16 (10)
17 (11)
18 (12)
19 (13)
20 (14)
32 (20)
33 (21)
34 (22)
35 (23)
80 (50)
84 (54)
126 (7E)
127 (7F)
* 'tx' indicates that the data can be transmitted from the DM1000, and
'rx' indicates that the data can be received by the DM1000.

2. Format Details

2.1 NOTE OFF
Reception
If [OTHER ECHO] is ON, these message are echoed from MIDI OUT.
If the [Rx CH] matches, these messages are received and used to control effects.
Note off message
STATUS 1000nnnn 8n
Note number
DATA 0nnnnnnn nn
Velocity(ignored)
0vvvvvvv vv
2.2 NOTE ON
Reception
If [OTHER ECHO] is ON, these messages are echoed from MIDI OUT.
If the [Rx CH] matches, these messages are received and used to control effects.
Note on message
STATUS 1001nnnn 9n
Note number
DATA 0nnnnnnn nn
Velocity(1-127:on, 0:off)
0vvvvvvv vv
2.3 CONTROL CHANGE
Reception
If [Control Change ECHO] is ON, these messages are echoed from MIDI OUT.
If [TABLE] is selected, these message are received if [Control Change Rx] is ON,
and will control parameters according to the [Control assign table] settings.
The parameters that can be set are defined in the Control Change Assign Pa-
rameter List.
If [NRPN] is selected, these messages are received if [Control Change Rx] is ON
and the [Rx CH] matches, and will control the parameter that is specified by the
four messages NRPN control number (62h, 63h) and Data Entry control num-
ber (06h, 26h). Parameter settings are defined in the Control Change Assign Pa-
rameter List.
353
rx/tx function
rx/tx DM1000-specific parameter change
rx/tx DM1000-specific parameter change
rx/tx General purpose digital mixer
parameter change
rx/tx General purpose digital mixer
parameter request
tx/rx function
tx/rx Edit buffer
tx/rx Patch data
tx/rx Setup data
tx/rx Backup data
tx/rx Cascade data
tx/rx Function (recall, store, title, clear)
rx Function (pair, copy)
rx Function (effect)
tx/rx Sort table
tx/rx Function (attribute, link)
rx Key remote
tx/rx Remote meter
tx/rx Remote time counter
tx/rx Automix status
tx/rx Function response (recall, store,
title, clear)
tx/rx Function response (attribute, link)
tx/rx System Attribute
tx Active sense
(8n)
(9n)
(Bn)
DM1000—Bedienungsanleitung