Mixing Paints For Use; Turning Airbrush Compressor On / Off; Regulating The Air Pressure; Regulating The Spraying Results - Parkside PABK 60 A1 Bedienungsanleitung

Preparations for use
Note: For optimal results, professionals connect
an intermediate pressure reducer (not included
with delivery). The pressure reducer can be used
to adjust the compressed air at the spray gun
and optimise it to your needs.
Note: During use of the blow gun
corresponding hose
compressor , there is a small discharge ope-
2 a
ning on the adapter
serves to create a more uniform airflow for ea-
sier and better handling of the blow gun
is not a defect, rather, it serves for better hand-
ling and an improvement of the spray results by
means of a uniform airflow.

Mixing paints for use

The paints included are water-soluble. In order to
properly apply the paints, add water and stir. As
delivered, the paints are too viscous.
First fill the beaker with your selected paint
colour with water.
Now screw the cover back on the beaker and
shake it.
Now use the pipette
of the slightly diluted paint paste and add them
to a paint mixing beaker completely filled with
water ( , ).
4 5
Shake the beaker. Now your paint has reached
the correct consistency.
Attach the paint mixing glass (
ing to Ill. B.
Note: If desired, you can adjust the amount of
water added to influence the colour intensity
yourself as with a watercolour box. The more
water you add, the „thinner" the colour.
You can also mix individualised colour tones
from the available colour pastes. Please take
note, there must be no paint clumps remaining
in the paint containers. The consistency should
correspond to that of water.
Note: If the paint used does not cover well, in-
crease the amount of paint in the mixture ratio.
10 GB/IE
73868_par_Airbrush_Set_Content_FI-SE-DK.indd 10
with the
9
incl. adapter for the
2
, which releases air. This
2 a
. This
9
to remove two drops
11
, ) accord-
4 5
Turning airbrush compressor
on / off
Turn the airbrush compressor
on / off switch to the position "I" (see Ill. C).
14
Turn the airbrush compressor
the on / off switch in the position "0" (see
14
Ill. C).
Note: Full pressure is built up after two seconds.

Regulating the air pressure

Regulate the air pressure by actuating the vent
of the air blow gun
9
extent.
ATTENTION! The device has a pressure switch,
which periodically and automatically turns the de-
vice off if there is excess pressure or if it is not in use.
Shortly before reaching the switch-off point, the
compressor runs more roughly and vibrates. This
may also be the case when re-started under load.
The performance and functionality are not impaired
by this. This is not a defect, rather, serves to protect
the compressor from overloading.
Note: The blow pistol
9
discharge openings even without actuating the trig-
ger. This is NOT A DEFECT.
Through actuating the trigger, the air discharge is
increased so that more air volume flows.
Note: During use of the blow gun
responding hose incl. adapter for the compres-
2
sor , there is a small discharge opening on the
2 a
adapter , which releases air. This serves to create
2 a
a more uniform airflow for easier and better handling
of the blow gun . This is not a defect, rather, it
9
serves for better handling and an improvement of
the spray results by means of a uniform airflow.

Regulating the spraying results

Regulate the amount of the paint supplied by
turning the paint nozzle of the spray stylus to
the right or left (see Ill. B).
on by setting the
1
off by setting
1
to more or less of an
blows air through the
with the cor-
9
06.07.12 12:36