Guarantee Conditions - SATA spray master RP Betriebsanleitung

SATA spray master RP | 8
Malfunction Cause
Spray gun does not Clogged air piston
shut-off air seat or worn air
piston.
Material bubbles or Atomization air
"boils" in the cup flows through the
paint channel to
the cup. The paint
nozzle is not suf-
ficiently tightened.
Air nozzle is not
completely screwed
on, the air net
clogged and the
seat is defective
or nozzle insert is
damaged.
Corrosion on air Cleaning solu-
cap thread, inside tion (water-based)
material passages remains inside/on
(material connec- the spray gun for
tion) or on spray too long.
gun body
Unsuitable cleaning
agent
Material leaks from Defective or miss-
behind the paint ing paint needle
needle sealing. sealing.
Clogged or dam-
aged paint needle.
Spray gun leaks Contamination
from the fluid tip between paint nee-
("fluid tip aper- dle tip and fluid tip.
ture").
Damaged nozzle
set.

10. Guarantee conditions

SATA offers a 12 months warranty on spray guns. This warranty
starts with the date when the end user purchases the device.
The warranty covers the value for production parts or defects
in material during the warranty period. The warranty does not
include damages caused by improper handling, normal wear and
tear, mechanical damages, faulty assembly, improper mainte-
nance, unusual spray materials, substitute materials, chemicals
such as alkaline solutions and acids, electro-chemical or electric
influences, as far as this damage is not the result of any error
committed by us. Abrasive spray material such as red lead and
liquid grinding material etc. reduce the lifetime of valves, pack-
ings, guns and nozzles. Wear and tear damage caused by this
are not covered in this warranty. Units should be inspected upon
delivery by the consumer. Obvious damage must be reported
within 14 days of receipt of the unit to the supplier to avoid loss
of the right to claim notice of defects. Additional claims such
as compensation are excluded. This refers as well to damages
caused during meetings , training sessions, or demonstrations.
Should the consumer require immediate repair or replacement
before a determination of whether the affected unit is covered
by the warranty, the repair or the replacement will be made and
charged at the current prices. If it is determind that the item is
covered by the warranty, a credit will be issued for the repair or
replacement. Replaced parts become the property of SATA or
their distributor. Notice of defects or other claims do not entitle
the consumer to delay or refuse payment. Returned merchan-
dise to SATA must be sent prepaid. All service charges, freight
Corrective Action
and handling charges are to be paid by the consumer. The
Clean air piston
charges made will be in accordance with the currently existing
seat and/or air pis-
pricing. Suretyships may not prolong the warranty period. This
ton, exchange air
warranty terminates upon unauthorized inference.
piston packing
Tighten parts
ATTENTION!
accordingly, clean
or replace.
When using solvents and cleaning liquids based on halogen-
ated hydrocarbons, e.g. 1.1.1-trichlorethylene and methylene
chloride, chemical reactions can occur, affecting the aluminium
cup, the gun body as well as all galvanised components (small
amounts of water added to 1.1.1-trichlorethylene lead to the
formation of hydrochloric acid). As a result, components may
oxidate, and in extreme cases the reaction can be even explo-
sive. Therefore, only use solvents and cleaning liquids which
do not contain any of the aforementioned substances. Never
use acids, alkaline solutions / lyes or any sort of stripping
agents for cleaning.
11. Important Note
Cleaning, please
observe chapter
Never point paint spray guns at yourself, at other persons or ani-
9, have spray gun
mals. Solvents and thinners can cause burns. Only the respec-
body exchanged
tive quantities of solvents and paints required for work progress
may be present in the direct surroundings of the unit (after work,
solvents and paints are to be returned to their assigned storage
rooms). Prior to any repair work the unit must be disconnected
from the air supply.
Exchange/Replace
paint needle seal-
Prior to putting the unit into operation, especially after each
ing
cleaning and each repair work, check all screws and nuts for
Exchange nozzle tight fit, as well as the sealing performance of the spray guns
set, exchange paint
and hoses.
needle sealing if
Defective components must be replaced or repaired accordingly.
necessary
To obtain best possible coating results, and for maximum safety,
Clean fluid tip
only use original spare parts.
and paint needle,
observe chapter 9
No sources of ignition (e.g. open flames, burning cigarettes,
Replace nozzle set
lamps without ex-protection etc.) may be present during painting,
as easily flammable mixture are generated during the painting
process. Occupational safety regulations must be applied when
painting (respiratory protection, etc.). Appropriate ear protection
muffs are required, as a sound level of 90 dB(A) is exceeded
when coating with higher pressure levels.
No vibration is transmitted to the upper parts of the operator's
body during use of the paint spray gun. Recoil forces are neg-
ligible.
EN