Wahl 1245 Bedienungsanleitung Seite 13

Operation
Preparation
Keep the packaging material for safe storage or
transport later.
f Check that the contents are complete.
f Check all the parts for possible transport damage.
Safety
Caution! Damage due to incorrect power
supply.
f Only operate the appliance with the voltage
stated on the nameplate.
Mains operation
1. Connect to the mains power supply (Fig. 2)
2. Switch on the appliance using the on/off switch and
switch off after use (Fig. 3).
The appliance has two speed settings. These can
be selected via the on/off switch.
Setting I = slow speed
Setting II = high speed
Operation
Cutting with the attachment comb
The appliance can also be operated with attachment
combs. Attachment combs can be used to extend the cut-
ting length range.
Attaching/removing the attachment comb
1. Fit the attachment comb onto the bottom edge of the
blade set (Fig. 4ⓐ) and push it over the cutting edge of
the bottom blade until it locks (Fig. 4ⓑ).
2. Push the attachment comb towards the cutting edge
of the bottom blade (Fig. 5) and remove it from the
blade set.
Changing the blade set
1. Switch off the appliance using the on/off switch (Fig. 3).
2. Press the release button (B) (Fig. 6ⓐ) towards the
blade set and lift the blade set out of the housing
(Fig. 6ⓑ).
3. Remove the blade set from the clip (Fig. 6ⓒ).
4. Attach the new blade set onto the clip (Fig. 8ⓐ).
Ensure that the clip is folded out. If this is not the
case, you can fold out the clip with a flat screw-
driver (Fig. 7).
5. Switch the appliance on (Fig. 3), then push the blade
set against the hand-held appliance until it audibly
clicks into place and the blade moves (Fig. 8ⓑ).
Maintenance
Warning! Injuries and material damage due to
incorrect handling.
f Switch off the appliance before cleaning it or
performing any maintenance. Disconnect the
appliance from the power supply.
Cleaning and care
Danger! Electric shock due to penetration of
liquid.
f Do not immerse the appliance in water!
f Do not allow any liquid to get inside the
appliance.
f Only reconnect the appliance to the power
supply if it is completely dry.
Caution! Danger from aggressive chemicals.
Aggressive chemicals could damage the appli-
ance and accessories.
f Never use solvents or scouring agents.
f Only use cleaning agents and blade set oil
recommended by the manufacturer.
Accessories and spare parts are available from
your dealer or our service centre.
f Remove the attachment comb (Fig. 5) after every use
and lift the blade set out of the casing (Fig. 6). Use the
cleaning brush to remove any cut hairs from the hous-
ing opening and from the blade set (Fig. 9).
Caution! Injuries due to incorrect handling.
f The blade set must not be unscrewed.
f The top blade must not be pushed out
completely!
f Push the top blade to the side (Fig. 9ⓐ) and remove
cut hairs from the top and bottom blade using the
cleaning brush. After cleaning, return the top blade to
its initial position (Fig. 9ⓑ). The top blade should be
aligned in the centre of the bottom blade.
f After cleaning the blade set, we recommend using
hygienic spray. It keeps all blade sets hygienically clean
and is effective against bacteria and viruses.
f Oil the blade set with the blade set oil (Fig. 10).
f We recommend that you clean and care for your blade
set during and after clipping with Blade Ice spray. The
Blade Ice spray ensures instant cooling, oiling and
cleaning of the blade set, while also protecting against
corrosion.
f Reattach the blade set after cleaning (Fig. 7/8). Switch
the appliance on briefly (approx. 10 seconds) to ensure
the oil film is evenly distributed.
f For a good and long-lasting cutting perfor-
mance, it is important to oil the blade set
frequently.
f If the cutting performance deteriorates after
long use despite regular cleaning and oiling,
the blade set should be replaced.
ENGLISH
de
en
fr
it
es
pt
nl
da
sv
no
fi
tr
pl
cs
sk
hr
hu
sl
ro
bg
ru
uk
et
lv
lt
el
ar
13