Herunterladen Inhalt Inhalt Diese Seite drucken

Mounting And Operation; Maintenance And Inspection - Hitachi DV 14DCL2 Bedienungsanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 7
English

MOUNTING AND OPERATION

Action
Removing and inserting the
battery
Charging
Tightening torque adjustment
Selecting the drill position
Selecting the impact position
Change rotation speed
Mounting the bit
Reversing the rotational direction
Switch operation
Using the bit holder
Selecting accessories

MAINTENANCE AND INSPECTION

1. Inspecting the tool
Since use of as dull tool will degrade effi ciency and
cause possible motor malfunction, sharpen or replace
the tool as soon as abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very "heart" of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Cleaning on the outside
When the impact driver drill is stained, wipe with a soft
dry cloth or a cloth moistened with soapy water. Do not
use chloric solvents, gasoline or paint thinner, for they
melt plastics.
5. Storage
Store the impact driver drill in a place in which the
temperature is less than 40°C and out of reach of
children.
NOTE
Make sure that the battery is fully charged when stored
for a long period (3 months or more). The battery with
smaller capacity may not be able to be charged when
used, if stored for a long period.
NOTE
Storing lithium-ion batteries.
Make sure the lithium-ion batteries have been fully
charged before storing them.
Prolonged storage of batteries with a low charge
may result in performance deterioration, signifi cantly
reducing battery usage time or rendering the batteries
incapable of holding a charge.
However, signifi cantly reduced battery usage time may
be recovered by repeatedly charging and using the
batteries two to fi ve times.
If the battery usage time is extremely short despite
repeated charging and use, consider the batteries dead
and purchase new batteries.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
Important notice on the batteries for the Hitachi
cordless power tools
Please always use one of our designated genuine
Figure
Page
batteries. We cannot guarantee the safety and
performance of our cordless power tool when used with
1
122
batteries other than these designated by us, or when
2
122
the battery is disassembled and modifi ed (such as
disassembly and replacement of cells or other internal
3
122
parts).
4
122
4
122
GUARANTEE
5
122
We guarantee Hitachi Power Tools in accordance with
6
122
statutory/country specifi c regulation. This guarantee does
not cover defects or damage due to misuse, abuse, or
7
123
normal wear and tear. In case of complaint, please send
8
123
the Power Tool, undismantled, with the GUARANTEE
9
123
CERTIFICATE found at the end of this Handling instruction,
to a Hitachi Authorized Service Center.
124
Information concerning airborne noise and vibration
The measured values were determined according to
EN60745 and declared in accordance with ISO 4871.
Measured A-weighted sound power level: 96 dB (A)
Measured A-weighted sound pressure level: 85 dB (A)
Uncertainty K: 3 dB (A).
Wear hearing protection.
Vibration total values (triax vector sum) determined
according to EN60745.
Impact drilling into concrete:
Vibration emission value
Uncertainty K = 2.4 m/s
Drilling into metal:
Vibration emission value
Uncertainty K = 1.5 m/s
The declared vibration total value has been measured in
accordance with a standard test method and may be used
for comparing one tool with another.
It may also be used in a preliminary assessment of exposure.
WARNING
○ The vibration emission during actual use of the power
○ Identify safety measures to protect the operator that
NOTE
Due to HITACHI's continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
6
a
h , ID = 13.5 m/s
2
a
h , D = 2.4 m/s
2
tool can diff er from the declared total value depending in
the ways in which the tool is used.
are based on an estimation of exposure in the actual
conditions of use (taking account of all parts of the
operating cycle such as the times when the tool is
switched off and when it is running idle in addition to the
trigger time).
2
2

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Dv 18dcl2

Inhaltsverzeichnis