Specifications; Important Safety Instructions - Makita AN902 Gebrauchsanleitung

ENGLISH
(Original instructions)
1 Pneumatic tool oil
2 Adjuster
3 Protrusion
4 Hole
5 Nose adapter
6 Door
7 Latch lever

SPECIFICATIONS

Model
Air pressure
Nail length
Nail capacity
Min. hose diameter
Pneumatic tool oil
Dimensions (L x W x H)
Net weight
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for the preliminary interior work such
as fixing floor joists or common rafters and framing work
in 2" x 4" housing.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: WHEN USING
SAFETY PRECAUTIONS
FOLLOWED TO REDUCE THE RISK OF PERSONAL
INJURY, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
• For personal safety and proper operation and mainte-
nance of the tool, read this instruction manual before
using the tool.
• Always wear safety glasses to protect your eyes from
dust or nail injury.
WARNING:
It is an employer's responsibility to enforce the use of
safety eye protection equipment by the tool operators
and by other persons in the immediate working area.
• Wear hearing protection to protect your ears against
exhaust noise and head protection. Also wear light but
not loose clothing. Sleeves should be buttoned or
rolled up. No necktie should be worn.
• Rushing the job or forcing the tool is dangerous. Han-
dle the tool carefully. Do not operate when under the
influence of alcohol, drugs or the like.
Explanation of general view
8 Magazine cap
9 Coil support plate
10 Graduation
11 Feed Claw
12 Air fitting
13 Air socket
14 Trigger
ENE059-1
ENB090-4
THIS TOOL, BASIC
SHOULD ALWAYS BE
15 Change lever
16 Hammer
17 Small rod
18 Drain cock
19 Air filter
20 Oiler
21 Pneumatic oil
AN902
0.49 – 0.83 MPa (4.9 – 8.3 bar)
Wire-collated coil nail 45 mm – 90 mm
150 – 300 pcs.
6.5 mm
Turbine oil
318 mm x 128 mm x 378 mm
3.5 kg
• General Tool Handling Guidelines:
1. Always assume that the tool contains fasteners.
2. Do not point the tool toward yourself or anyone
whether it contains fasteners or not.
3. Do not activate the tool unless the tool is placed
firmly against the workpiece.
4. Respect the tool as a working implement.
5. No horseplay.
6. Do not hold or carry the tool with a finger on the trig-
ger.
7. Do not load the tool with fasteners when any one of
the operating controls is activated.
8. Do not operate the tool with any power source other
than that specified in the tool operating/safety
instructions.
• An improperly functioning tool must not be used.
• Sparks sometimes fly when the tool is used. Do not use
the tool near volatile, flammable materials such as gas-
oline, thinner, paint, gas, adhesives, etc.; they will
ignite and explode, causing serious injury.
• The area should be sufficiently illuminated to assure
safe operations. The area should be clear and litter-
free. Be especially careful to maintain good footing and
balance.
• Only those involved in the work should be in the vicin-
ity. Children especially must be kept away at all times.
• There may be local regulations concerning noise which
must be complied with by keeping noise levels within
prescribed limits. In certain cases, shutters should be
used to contain noise.
• Do not play with the contact element: it prevents acci-
dental discharge, so it must be kept on and not
removed. Securing the trigger in the ON position is also
very dangerous. Never attempt to fasten the trigger. Do
not operate a tool if any portion of the tool operating
controls is inoperable, disconnected, altered, or not
working properly.
7