Specifications; Functional Description - Makita JS3200 Betriebsanleitung

ENGLISH
(Original instructions)
1 Switch trigger
2 Lock button
3 Gauge for stainless: 2.5 mm
(3/32")
4 Gauge for mild steel: 3.2 mm
(1/8")
5 Hex wrench

SPECIFICATIONS

Model
Max. cutting capacities
Steel up to 400 N/mm
Steel up to 600 N/mm
Steel up to 800 N/mm
Aluminum up to 200 N/mm
Min. cutting radius ................................................ 50 mm
Strokes per minute (min
Overall length ..................................................... 204 mm
Net weight ............................................................. 3.4 kg
Safety class .............................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for cutting sheet steel and stainless
sheet steel.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
SHEAR SAFETY WARNINGS
1. Hold the tool firmly.
2. Secure the workpiece firmly.
3. Keep hands away from moving parts.
4. Edges and chips of the workpiece are sharp.
Wear gloves. It is also recommended that you
put on thickly bottomed shoes to prevent injury.
5. Do not put the tool on the chips of the work-
piece. Otherwise it can cause damage and trou-
ble on the tool.
6. Do not leave the tool running. Operate the tool
only when hand-held.
4
Explanation of general view
6 Lower blade
7 Upper blade securing bolt
8 Upper blade
9 Tighten
10 Blade holder
11 No gap allowed
12 Lower blade positioning bolt
2
....................... 3.2 mm (10 ga.)
2
....................... 2.5 mm (13 ga.)
2
....................... 1.5 mm (17 ga.)
2
................. 4.0 mm (9 ga.)
-1
) ..................................... 1,600
7. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
JS3200
high locations.
8. Do not touch the blade or the workpiece immedi-
ately after operation; they may be extremely hot
and could burn your skin.
9. Avoid cutting electrical wires. It can cause seri-
ous accident by electric shock.
SAVE THESE INSTRUCTIONS.
WARNING:
/II
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruc-
tion manual may cause serious personal injury.
ENE037-1

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
ENF002-1
tool.
Switch action (Fig. 1)
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
GEA010-1 To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
For continuous operation, pull the switch trigger and then
push in the lock button.
To stop the tool from the locked position, pull the switch
trigger fully, then release it.
Permissible shearing thickness (Fig. 2)
The groove on the yoke serves as a thickness gauge for
shearing mild or stainless steel plate. If the material fits
GEB027-2
within the groove, it is shearable.
The thickness of materials to be sheared depends upon
the type (strength) of the material. The maximum shear-
ing thickness is indicated in the table below in terms of
various materials. Attempting to shear materials thicker
than indicated will result in tool breakdown and/or possi-
ble injury. Keep within the thickness shown in the table.
Max. cutting capacities
Steel up to 400 N/mm
Steel up to 600 N/mm
Steel up to 800 N/mm
Aluminum up to 200 N/mm
13 Hex nut
14 Thickness gauge
15 Workholder
16 Cutting line
17 Limit mark
18 Screwdriver
19 Brush holder cap
mm
2
3.2
2
2.5
2
1.5
2
4.0
ga
10
13
17
9