Specifications; Additional Safety Rules For Tool - Makita JR180D Betriebsanleitung

ENGLISH
1 Battery cartridge
2 Push button
3 Charging light
4 Battery charger
5 Released position
6 Fixed position

SPECIFICATIONS

Model
Length of stroke .................................................... 23 mm
Strokes per minute ........................................... 0 – 2,700
Cutting capacities
Pipe ................................................................... 90 mm
Wood ................................................................. 90 mm
Overall length ..................................................... 469 mm
Net weight (with battery cartridge) ........................ 3.5 kg
Rated voltage ................................................... D.C. 18 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
1. SAVE THESE INSTRUCTIONS — This manual
contains important safety and operating instruc-
tions for battery charger.
2. Before using battery charger, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
3. CAUTION — To reduce risk of injury, charge only
MAKITA type rechargeable batteries. Other types
of batteries may burst causing personal injury
and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or sold
by the battery charger manufacturer may result
in a risk of fire, electric shock, or injury to per-
sons.
6. To reduce risk of damage to electric plug and
cord, pull by plug rather than cord when discon-
necting charger.
7. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress.
8. Do not operate charger with damaged cord or
plug — replace them immediately.
9. Do not operate charger if it has recieved a sharp
blow, been dropped, or otherwise damaged in
any way; take it to a qualified serviceman.
10. Do not disassemble charger or battery cartridge;
take it to a qualified serviceman when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock or fire.
4
Explanation of general view
7 Blade clamp sleeve
8 Blade
9 Lever
10 Shoe
11 Switch trigger
12 Lock-off button
11. To reduce risk of electric shock, unplug charger
JR180D
ADDITIONAL SAFETY RULES FOR CHARGER
& BATTERY CARTRIDGE
1.
2.
3.
4.
5.
6.
7.
8.
9.

ADDITIONAL SAFETY RULES FOR TOOL

1.
2.
3.
4.
13 Press in
14 Limit mark
15 Screwdriver
16 Brush holder cap
from outlet before attempting any maintenance
or cleaning. Turning off controls will not reduce
this risk.
Do not charge battery cartridge when tempera-
ture is BELOW 10°C (50°F) or ABOVE 40°C
(104°F).
Do not attempt to use a step-up transformer, an
engine generator or DC power receptacle.
Do not allow anything to cover or clog the
charger vents.
Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.
Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
Be careful not to drop, shake or strike battery.
Do not charge inside a box or container of any
kind. The battery must be placed in a well venti-
lated area during charging.
Be aware that this tool is always in an operating
condition, because it does not have to be
plugged into an electrical outlet.
Wear a hard hat (safety helmet), safety glasses
and/or face shield. It is also highly recom-
mended that you wear a dust mask, ear protec-
tors and thickly padded gloves.
Check the blade carefully for cracks or damage
before operation. Replace cracked or damaged
blade immediately.
Do not attempt to cut workpieces larger than
specified in this manual (especially hollow pipe).
The blade might snap and cause an injury.
(Fig. 1)