Intended Use; Explanation Of The Symbols; Safety Instructions - Conrad 75 43 16 Bedienungsanleitung

O P E R A T I N G I N S T R U C T I O N S
LAN Colour Camera
Item no. 75 43 16

Intended use

The product is intended for surveillance by means of the integrated camera. The operation
takes place via a wired 10/100MBit network (RJ45 connector).
The product must not get damp or wet, it is intended only for use in dry, indoor locations.
The power for the camera is supplied via the wall plug transformer included in the delivery.
Please bear in mind that it is prohibited by law to observe strangers with a camera without
their knowledge and consent. Observe the rules and regulations of the country where you are
using the camera.
The safety instructions and technical data must be followed without fail!
Any use other than that described above may damage the product. Moreover, this may give
rise to hazards such as short-circuiting, fi re, electric shock, etc. No part of the product may be
modifi ed or converted!
This product complies with the applicable national and European requirements. All names of
companies and products are the trademarks of the respective owner. All rights reserved.
Contents
• Camera
• Network cable
• Mounting bracket with mounting material
• Wall plug transformer
• CD
• Operating instructions of the manufacturer in English (either as hardcopy or as PDF on a CD)
• Quickly guide

Explanation of the Symbols

The lightning symbol indicates a health hazard, e.g. electric shock.
This symbol indicates specifi c risks associated with handling, function and use.
☞
The "arrow" symbol indicates special tips and operating information.

Safety Instructions

The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any consequen-
tial damage!
We do not assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions. In such cases,
the warranty will be null and void.
• The unauthorised conversion and/or modifi cation of the product is not permitted for
safety and approval reasons (CE). Never dismantle the product.
• The product is not a toy and must be kept out of the reach of children. It should be
operated out of the reach of children.
• The use of the surveillance camera system does not replace the personal supervi-
sion of children, or people who require special assistance, but only serves as a
support to this supervision.
• The design of the wall plug transformer complies with Protection Class II. Only
connect the wall plug transformer to a standard wall socket connected to the public
supply.
• The product should only be used in dry indoor areas, it must not become damp or
wet! There is a risk of a lethal electric shock!
• The camera should not be exposed to extreme temperatures, direct sunlight,
strong vibrations or heavy mechanical stress.
• Make sure that the connection cable is not pinched or damaged by sharp edges.
• Do not leave packing materials unattended. They may become dangerous
playthings for children.
www.conrad.com
Version 02/13
Getting started, Connection via RJ45
☞
• Connect the camera's RJ45 connector to a 1:1 connected network cable and its network, e.g.
a network switch.
• Connect the low voltage connector of the camera via the AC adaptor included in the delivery
to a power socket (230V~/50Hz).
There are two LEDs in the RJ45 plug: The LED on the top right indicates the link status (net-
work cable/connection ok), the LED on the top left indicates data transfer via the LAN cable.
The camera is started after a few seconds and the blue LED at the front should be fl ashing.
• Insert the provided CD into the appropriate drive on your computer and start the installation
programme (programme name "IPCamSetup.exe").
Follow all the software instructions. Windows needs to be restarted afterwards.
Please note that the names and descriptions of the installation procedure, as described here,
may be different in newer versions of the software. For this procedure, observe the enclosed
manufacturer's operating instructions
• After having started the programme just installed ("IP Camera Tool"), it searches for available
cameras within the network. If the camera is shown with its respective IP address, double-
click on it.
☞
• A request to enter username and password appears. Enter "admin" as username (lower case
letters and without quotation marks), the fi eld for the password remains empty (do not enter
anything here).
• Click "OK" and then the respective "Sign in" button in the next window depending on the
internet browser you are using.
• Depending on the security settings for your Internet Explorer an error message appears, say-
ing a required ActiveX element cannot be installed or that the installation of the ActiveX can
be started manually by clicking on the information bar.
This ActiveX element is necessary for displaying the camera image. Please note that the
ActiveX software for the Internet Explorer offers more settings than the software for other
Internet browsers.
• Furthermore, it may be necessary to make modifi cations to the settings for the antivirus or
fi rewall programmes before the software will function properly.
Unfortunately, description of the precise procedure is not possible due to several pro-
grammes.
• For further information concerning the software, refer to the CD provided or the manufac-
turer's operating instructions.
• Handle the product with care, it can be damaged by impact, blows, or accidental
dropping, even from a low height.
• If the camera is used with other devices (e.g. a monitor), the operating instructions
and safety notices for these devices must be followed.
• A safe operation can no longer be assumed, if:
- the device is visibly damaged,
- the device no longer works
- the device has been stored under adverse conditions.
- it was exposed to heavy loads during transport
• In commercial institutions, the accident prevention regulations of the Employer's
Liability Insurance Association for Electrical Systems and Operating Materials
are to be observed.
• Disconnect the power supply from the camera, if it is not to be used for a while (e.g.
for storage).
• If you have any questions that are not answered in this manual, please contact our
technical service or another specialist.
Test the camera before permanently installing it in the desired place.
To make all the settings, the camera should always be connected fi rst to the
computer via RJ45. Only when the camera works properly can WLAN operation
be set up.
For an easy setup it is strongly recommended that a DHCP server (e.g. contained in
every router) is active in your network.
Note: There must be a DHCP server activated in your network (e.g. the DHCP serv-
er in a router). The PC must be confi gured so it assigns an IP address automatically.