Index Search; Time Search - AEG VCR 4500 Bedienungsanleitung

HG462ED(EN).fm Page 13 Wednesday, March 3, 2004 7:49 PM
QUICK-FIND
This function enables you to search and confirm the contents
of the recorded programme(s) using the index mark.
• Use the remote control for this procedure.
• The tape must be fully rewound.
1) Press QUICK-FIND .
To Skip to the Beginning of Next Programme
1) Press QUICK-FIND .
To View at Normal Speed
1) Press PLAY / . The Quick-Find is cancelled.
o
Note: • This function will not operate in the Recording mode.
•
When you want to cancel the Quick-Find while in
progress, press STOP /
•
When the end of a tape is reached during the Quick-
Find, the tape will automatically rewind to the
beginning. After rewinding finishes, the VCR will
eject the tape and turn itself off.

INDEX SEARCH

• The index mark will be made automatically when
REC/OTR
is pressed. It will also be marked at the starting
point of Timer recording and OTR.
• The index mark is not recorded if
and released during recording.
• The time gap between index marks on the tape should be
greater than 1 minute for SP recording and 2 minutes for
LP recording.
• Use the remote control for this procedure.
1) Press SEARCH MODE .
2) Press PLAY / or STOP /
o L
programmes that you want to skip appears.
3) Press REW / or F.FWD /
s B
The VCR begins rewinding or fast forwarding to the
beginning of desired programme.
When the preset programme is reached, the VCR will start
playback automatically.
Note: •
Index Search can be set up to 20.
• This function will not operate in the Recording mode.
• Operations must be followed up within 30 seconds,
from steps 2) to 3) . Otherwise the Index Search mode
will be cancelled.
• To exit the Index Search mode, press
STOP
Or press / after step
L

TIME SEARCH

If a tape includes both programmes recorded in the PAL
system and ones recorded in the NTSC system, this function
may not be operated correctly.
• Use the remote control for this procedure.
1) Press SEARCH MODE twice.
2) Press PLAY / or STOP /
o L
time appears.
3) Press REW / or F.FWD /
s B
The VCR begins rewinding or fast forwarding to the
specified point.
When 0:00 is reached, the VCR will start playback
automatically.
Note: •
Time Search can be set up to 9 hours 59 minutes
(9:59).
•
This function will not operate in the Recording mode.
.
L
PAUSE/STILL
is pressed
repeatedly until the number of
.
MENU in step 2) .
3)
.
repeatedly until the desired
.
13
• Operations must be followed up within 30 seconds,
2) 3)
from steps to . Otherwise the Time Search mode
will be cancelled.
•
To exit the Time Search mode, press
Or press STOP / after step
L
Copying a Video Tape
You can make copies of videotapes made by friends or relatives
for your own enjoyment.
WARNING:
• Unauthorized recordings of copyrighted video
tapes may be an infringement of copyright
laws.
Connect the recording VCR (this unit), playing VCR (another
VCR) and your TV as outline in the following diagram.
[Source (Playing) VCR <Monaural>]
(Use for monitoring)
(another VCR)
to 21-Pin
Scart Jack
AV2 (DECODER)
[Editing (Recording) VCR]
(this unit)
1) Insert a pre-recorded videocassette into the playing VCR.
2) Insert a blank videocassette, or one you want to record
over, into the cassette compartment of the recording
VCR.
3) Press SPEED/SYSTEM on the remote control to select the
desired recording speed (SP/LP).
4) Select "AV2" position on the recording VCR. See "Other
Connections".
5) Press REC/OTR on the recording VCR.
6) Begin playback of the tape in the playing VCR.
7) To stop recording, press STOP/EJECT
VCR, then stop playback of the tape in the playing VCR.
Note: •
For best results during dubbing, use the VCR's front
panel controls whenever possible. The remote control
might affect the playback VCR's operation.
• If video or colour fades in and out, you may be
copying a copy guarded video tape.
To Monitor the Recording
Turn on the TV and select the video channel on the TV.
A Status Display
To check the Counter, or Clock & Channel number, press
DISPLAY DISPLAY
. Each time you press
change as illustrated:
When you select the channel using the
the desired channel (position number).
<OFF mode> <COUNTER mode>
■
SP
Press once.
0:12:34
Press once.
Note:
If the on screen display or indicators on the front panel
show an abnormal reading or no reading, unplug the
VCR for 2 minutes, then replug it again.
Please note that language, clock, and timer settings will
be cleared after disconnection.
MENU 2)
in step .
3) .
[TV set]
to aerial
socket
Coaxial cable (supplied)
AV1 (TV)
AUDIO
OUTPUT
AERIAL
L
RF OUT
R
to RF OUT
on the recording
, TV screen will
number buttons
, select
<CLOCK and CHANNEL
NUMBER mode>
■
17:40
SP
P02
Press once.
EN