Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
HG462ED(EN).fm Page 6 Wednesday, March 3, 2004 7:49 PM
5) Press
MENU
.
MENU
TIMER
SET UP
INITIAL
Video Channel Setting
Video channel setting will be necessary, if your VCR is
connected to the TV via the coaxial cable.
• Use the remote control for this procedure.
1) Insert a pre-recorded tape into the VCR.
The VCR will turn on and start playback automatically.
If playback does not start, press
2) Select and adjust your TV to channel 36.
•If the playback picture appears on the TV screen,
continue with step
8)
.
•If channel 36 is set for broadcasting, or interference lines
appear on the picture, the RF converter must be set to a
different channel between CH22 and CH69. Continue
with step
3)
.
3) Press
MENU
.
4) Press
PLAY
/
or
STOP
/
o
L
"INITIAL". Then, press
F.FWD
5) Press
PLAY
/
or
STOP
/
o
L
OUT". Then, press
F.FWD
will appear.
6) Press
PLAY
STOP
/
or
/
o
L
used for broadcasted between channel 22 and channel 69
F.FWD
in your area, then press
7) Press
MENU
to exit.
Set the TV channel to the RF OUT CHANNEL which
was selected on the VCR. A picture from the VCR will
appear on the TV screen. If a picture does not appear,
3)
7)
repeat steps
to
using a different channel which is not
used for broadcasted.
8) Press
STOP
/
to stop the tape.
L
Note: •
You may also access the RF OUT CH menu by
pressing and holding
MENU
3 seconds during power off until the RF OUT CH
menu appears.
•
If this unit and your TV are connected using a scart
cable, the RF converter may be switched off to avoid
any possibility of interference. To switch off the RF
converter, follow steps
STOP
/
repeatedly until "- -" appears next to "RF
L
OUT CH." Press
F.FWD
INITIAL
CH TUNING
CLOCK
RF OUT
LANGUAGE
LANGUAGE
DEUTSCH
ITALIANO
ESPAÑOL
NEDERLANDS
FRANÇAIS
SVENSKA
[
]
ENGLISH
PLAY
/
.
o
repeatedly to select to
/
.
B
repeatedly to select to "RF
/
. The RF OUT CH menu
B
to select a channel which is not
/
.
B
on the remote control for
3)
to
5)
above and press
/
, then
MENU
to exit.
B
MENU
TIMER
SET UP
INITIAL
Setting the Clock
This VCR incorporates a 24-hour clock. The clock must be set
for the Timer Recording function to operate correctly.
• Use the remote control for this procedure.
1) Press
MENU
.
2) Press
PLAY
STOP
/
or
/
o
L
F.FWD
/
.
B
3) Press
PLAY
STOP
/
or
/
o
L
F.FWD
/
.
B
4) Press
PLAY
STOP
/
or
/
o
L
F.FWD
then press
/
.
B
5) Press
PLAY
/
or
STOP
/
o
L
appears, then press
F.FWD
6) Press
PLAY
/
or
STOP
/
o
L
then press
F.FWD
/
.
B
7) Press
PLAY
/
or
STOP
/
o
L
then press
F.FWD
/
.
B
8) Press
PLAY
/
or
STOP
/
o
L
appears.
9) Press
MENU
to start the clock.
Note:
• Press
REW
/
to go one step back from the current step
s
during steps
5)
to
8)
.
• Although seconds are not displayed, they begin counting
from 00 when you exit by pressing
to synchronize the clock with the correct time.
• If the VCR is unplugged or if there is a power failure for
more than 30 seconds, you may have to reset the clock.
MENU
TIMER
SET UP
INITIAL
6
INITIAL
CH TUNING
CLOCK
RF OUT
LANGUAGE
RF OUT CH 36
to select "INITIAL", then press
to select "CLOCK", then press
until the relevant year appears,
until the relevant month
/
.
B
until the relevant day appears,
until the relevant hour appears,
until the relevant minute
MENU
. Use this feature
INITIAL
CH TUNING
CLOCK
RF OUT
LANGUAGE
CLOCK
YEAR
2 0 0 4
MONTH
0 1
DAY
0 7 WE
_ _
HOUR
_ _
MINUTE
EN
Werbung
Kapitel
Inhaltsverzeichnis
Fehlerbehebung
