Channel Plan - AEG VCR 4500 Bedienungsanleitung

HG462ED(EN).fm Page 7 Wednesday, March 3, 2004 7:49 PM
Channel Presetting
Tuning of broadcast channels not already preset in the VCR
can be performed in two ways.
Automatic Channel Preset
• By "AUTOMATICALLY" tuning channels and placing
them in sequential order in the VCR's memory i.e. the first
channel found will be memorized into the VCR's channel
position 1, the second channel found will be memorized
into the VCR's channel position 2 and so on.
• Execution of the "Automatic" channel presetting cancels all
the preset channels. DO NOT use this feature if you intend
to use some of the pre-tuned channels. Use the "Manual"
channel presetting function to tune in the additional
channels you require.
Manual Channel Preset
• Each channel is tuned manually and individually. Follow
the steps laid out in the "Manual Channel Preset" section.
Before you preset Channel...
• It is necessary to set the video channel if your VCR is
connected to the TV via the coaxial cable, and TV channel
36 is set for broadcasting, or interference lines appear on
the picture. Please refer to "Video Channel Setting".
Automatic Channel Preset
You can programme the tuner to scan only the channels that
you can receive in your area.
• Use the remote control for this procedure.
1) Turn on the TV and select the TV channel to the video
channel on the TV.
2) Press MENU .
3) Press PLAY / or STOP /
o L
F.FWD / .
B
4) Press PLAY / or STOP /
o L
press F.FWD / .
B
5) Press PLAY / or STOP /
o L
F.FWD / .
B
• The tuner scans and memorizes all the active channels in
your area. After scanning, the tuner stops on the lowest
memorized channel.
MENU
TIMER
SET UP
INITIAL
scanning
to select "INITIAL", then press
to select "CH TUNING", then
to select "AUTO", then press
INITIAL
CH TUNING
CLOCK
RF OUT
LANGUAGE
CH TUNING
AUTO
MANUAL
MOVE
To Select a Desired Channel
You can select a desired channel by using
directly pressing the number buttons
• Enter a channel number as a two-digit number for the
quickest results. For example, to select channel 6, press
and 6 . If you only press 6 , channel 6 will be selected after a
brief delay.
• You can only select channels 1–99.
Manual Channel Preset
• Use the remote control for this procedure.
1) Press MENU .
2) Press PLAY / or STOP /
o L
F.FWD / .
B
3) Press PLAY / or STOP /
o L
press F.FWD / .
B
4) Press PLAY / or STOP /
o L
press F.FWD / .
B
5) Press PLAY / or STOP /
o L
F.FWD
press / .
B
•When a weak signal is received in Manual Tuning mode,
you can change the background to solid blue or the
TAPE COUNTER RESET
static screen by pressing
6) Press the number buttons
,
your desired position number, then press
•You can select position number 01-99.
•If [ON] appears on the right side of "SKIP", press
PLAY STOP
/ or / to point to "SKIP". Then, press
o L
F.FWD
/ to select [OFF].
B
•If you want to remove scrambled signals, press
PLAY STOP
/ or / repeatedly to point to
o L
"DECODER". Then, press
7) Press PLAY STOP
/ or /
o L
F.FWD
press / .
B
Press PLAY / or STOP /
o L
search up or down automatically. When a channel is
found, the VCR will stop searching and the picture will
appear on the TV Screen.
•You can select desired channel number by using
the number buttons . You must refer to the following
Channel Plan table and press three digits to select the
channel number.
(To select channel 24, press "
press " 2 " and " 4 ".)
•If this is the channel you want, press

Channel Plan

CH Indication
02 – 12
13 – 20
21 – 69
74 – 78
80 – 99,100
121 – 141
This VCR can receive Hyper and Oscar frequency bands.
8) Press MENU to exit.
7
CHANNEL ( / ), or
o p
on the remote control.
0
to select "INITIAL", then press
to select "CH TUNING", then
to select "MANUAL", then
to select "POSITION", then
.
PLAY STOP
/ , or / to select
o L
F.FWD
/ .
B
F.FWD
/ to select [ON].
B
to select "CHANNEL", then
. The VCR tuner will begin to
0 " button first and then
F.FWD .
/
B
TV Channel
E2 – E12
A – H (only ITALY)
E21 – E69
X, Y, Z, Z+1, Z+2
S1 – S20,GAP
S21 – S41
EN