Low Battery Indicator - DeWalt DCL043 Bedienungsanleitung

The minimum conductor size is 1,5 mm
maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.
WARNING: Operating equipment at low
voltage can cause it to overheat. Using
an excessively long extension cord can
cause the cord to overheat.
OPERATION
Installing and Removing the Battery
Pack (fi g. 4)
CAUTION: Make sure the lamp head is
in the OFF position before inserting the
battery to avoid injuring eyes.
NOTE: For best results, make sure your battery
pack is fully charged.
To install the battery pack (d) into the spotlight
handle, align the battery pack with the rails inside
the spotlight's handle and slide it into the handle until
the battery pack is firmly seated in the spotlight and
ensure that it does not disengage.
To remove the battery pack from the spotlight, press
the release button (e) and firmly pull the battery pack
out of the spotlight handle. Insert it into the charger
as described in the charger section of this manual.
For a list of compatible battery packs and chargers,
refer to Technical Data.
FUEL GAUGE BATTERY PACKS (FIG. 5)
Some D WALT battery packs include a fuel gauge
E
which consists of three green LED lights that
indicate the level of charge remaining in the battery
pack.
To actuate the fuel gauge, press and hold the fuel
gauge button (h). A combination of the three green
LED lights will illuminate designating the level of
charge left. When the level of charge in the battery
is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
NOTE: The fuel gauge is only an indication of the
charge left on the battery pack. It does not indicate
tool functionality and is subject to variation based
on product components, temperature and end-user
application.
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
Switch (fi g. 1, 3)
The spotlight has a high beam (i) and low beam (j)
setting. Press the switch (a) once for high beam,
2 ; the
twice for low beam, and a third time to turn the
spotlight off.

Low Battery Indicator

As the battery nears a fully discharged state, the
spotlight will blink twice and then dim, dropping
the brightness of the spotlight below the normal
level. The light will continue to blink twice every 45
seconds until the battery is fully discharged at which
time the light will turn off. Indication time will vary
based on battery pack capacity and the light setting.
Pivoting Head (fi g. 1)
The pivoting head rotates in six positions ranging
from 0°–90°.
Carrying and Suspending the Light
(fi g. 1)
CAUTION: When the spotlight hangs
by the belt hook or loop hook, do not
shake the light or the object from which
it hangs. Do not hang the spotlight from
any electrical wires or anything that is
not secure. Personal injury or property
damage may occur.
CAUTION: Only use the belt hook
or the loop hook for hanging the LED
spotlight. The belt hook and loop hook
are not intended to support additional
weight. Do not attach or hang anything
additional to the light or risk of breakage
may occur.
CAUTION: Do not use the belt hook or
loop hook to reach with or to support
your weight in any situation.
LOOP HOOK (FIG. 1)
The light may be carried or hung by the loop hook
(b). When not in use, the loop may be locked down.
BELT HOOK (FIG. 1)
WARNING: To reduce the risk of
serious personal injury, ensure the screw
holding the belt hook is secure.
IMPORTANT: When attaching or replacing the belt
hook (g), use only the screw (f) that is provided. Be
sure to securely tighten screw.
The belt hook (g) can be attached to either side
of the light using only the screw (f) provided, to
accommodate left- or right-handed users. If the
hook is not desired at all, it can be removed from
the light.
To move the belt hook, remove the screw (f) that
holds the belt hook in place, then reassemble on the
opposite side. Be sure to securely tighten screw.
ENGLISH
27