Before Using The Equipment - EINHELL GE-CM 36/47 HW Li Originalbetriebsanleitung

the equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is applied.
Warning!
This equipment generates an electromag-
netic fi eld during operation. Under certain
circumstances this fi eld may actively or pas-
sively impede medical implants. To reduce
the risk of serious or fatal injuries, we recom-
mend persons with medical implants to con-
sult their doctor and the manufacturer of the
medical implant prior to using the equipment.

5. Before using the equipment

The lawn mower is delivered partly assembled.
The push bar and the grass basket must be as-
sembled before using the lawn mower. Follow the
instructions step by step and refer to the pictures
when assembling.
Fitting the push bar (Fig. 3 to 6)
Insert the push bar holder (Fig. 2/Item 3) into the
handlebar mount and secure with the fastening
screw and nut (Fig. 4/5).
The top push bar (Fig. 1/Item 2) must be pushed
onto the push bar holders (Fig. 2/Item 3) and se-
cured as shown above in Fig. 6. Then fasten the
cable to the push bar by the cable clips (Item 13).
The push bar can be adjusted to 3 diff erent height
settings. To adjust the height, undo the fastening
nuts (Item 10) and move the bar into the required
lock (Fig. 3 to 6).
Warning!
Always set the identical handle height on both
sides.
•
Use the cable clips to align the cable with the
long handle (Fig. 5/Item 13).
Fitting the grass basket (see Fig. 7)
Before you fi t the grass basket you must ensure
that the motor is switched off and the blade is not
rotating. Also pull out the safety plug (12) and re-
move all the power batteries (16). Lift the ejector
fl ap (Fig. 7/Item 7) with one hand. With the other
hand, hold the grass basket by the handle and
hook it in from above (Fig. 7).
Anl_GE_CM_36_47_HW_Li_SPK9.indb 25 Anl_GE_CM_36_47_HW_Li_SPK9.indb 25
GB
Filling level indicator of the grass collector
(fi g. 16)
The grass collector is equipped with a fi lling level
indicator (Fig. 2/Item 15), which is lifted by the
airfl ow that the lawn mower generates during
operation. If this drops down onto the grass catch
basket during mowing, this means that the grass
collector is full and needs emptying.
Adjusting the cutting height
Caution!
Adjust the cutting height only when the machine
has been switched off , the safety plug (12) has
been pulled out and the batteries (16) removed.
Before you begin to mow, check to ensure that the
blade is not blunt and that none of the fasteners
are damaged. To prevent any imbalance, replace
blunt and/or damaged blades. To carry out this
check, fi rst switch off the motor and pull out the
safety plug.
Warning!
Adjust the cutting height only when the machine
has been switched off , the safety plug (12) has
been pulled out and the batteries (16) removed.
The cutting height is adjusted as follows
(see Fig. 11):
1. Push the lever (6) outwards.
2. Set the lever (6) to the desired cutting height.
3. Release the lever (6) and check that it is se-
curely seated in the lock.
Using the mulching adapter (Fig. 8a)
In mulching mode the cuttings are shredded in
the enclosed mower housing and then spread
back onto the lawn. It is not necessary to gather
and dispose of the grass.
Important! Mulching is only possible if the
lawn is relatively short.
Warning!
Insert the mulching blade only when the machine
has been switched off , the safety plug (12) has
been pulled out and the batteries (16) removed.
To use the mulching function, disconnect the
catch bag, slide the mulching adaptor (Fig. 5d/
Item 18) through the ejector opening and close
the ejector fl ap again.
- 25 -
10.11.2017 10:23:45 10.11.2017 10:23:45