Modifying A Washing Programme - Fagor FET-6412D Bedienungsanleitung

EN 4 / PROGRAMMING YOUR MACHINE
• DETAILS OF THE PROGRAMMES
• Rinsing
A separate rinse followed by a choice of:
— Either spin and drain
— Or drain only («Drip-dry» option)
— Or a stop with the drum full of
• Spinning
This allows a separate spin and drain.
Important:
In the case of «Rinse only» followed by a spin or «Spin only»,
ensure that you select a suitable spin speed for the type of washing in
the machine.
•
DETAILS OF THE OPTIONS
• Dose-e
This function is used to deactivate the automatic detergent distributor.
• Intensive
This function enables you to handle so-called 'difficult' stubborn stains.
With Dose ON, the distribution system automatically adds an appropriate
amount of additional detergent.
• Reducing the time
Allows for a reduction in the cycle time according to 2 levels that can
be accessed by pressing on the button several times. Level 1, reduces
the average time by 20%. Level 2 reduces the average time by 40% for
laundry that is only lightly soiled.
• Easy ironing
This option washes your laundry more gently, but with an identical washing
performance. The spin speed is slower so that your laundry creases less.
• Drip dry ( )
This function, for very delicate linen, enables you to remove spinning and
to pass directly to the draining of the washing machine.
• Full drum stop ( )
This function enables you to remove the washing from your machine
before the spin phase or to delay this phase with you washing remaining
in water to prevent creasing.
NB: When the machine stops with the drum full
of water, the «Spin» cycle progress light ( )
flashes and the remaining time displayed is
«00.00»
Then:
— Either you want to drain after spinning.
3
In this case, use the button
type of washing.
The programme will end automatically.
— Or you just want to drain.
In this case, use the button
speed « »).
• Delayed start
You can delay the start of your programme to use off-peak electricity or to
avoid your washing standing in the drum for too long at the end of the cycle.
To do this, press the button «+»
By repeatedly pressing the (+) button, select the time by which you wish
to delay the cycle start (in increments of 1 hour).
NB:
- The «-»button can be used to go backwards.
- The time remaining before the cycle start is counted down by the hour
until 1 hour and then by minutes from 59 minutes to 1 minute.
(continued)
waters.
to choose a suitable spin speed for your
3
to select the «Drip Dry» function (spin
.
5
Information:
Throughout the whole waiting period, four elements light up
in succession.
At the end of the waiting period, the programme starts and the
machine counts down the time remaining before the end of the cycle.

• MODIFYING A WASHING PROGRAMME

• During programming:
Anything can be changed before the «Start/Pause» button
• After the cycle has started:
If you want to change the type of fabric (e.g. from «COTTON» to
«SYNTHETICS») after you have pressed the «Start/Pause» button
have to cancel the current programme. To do this, turn the selector to
Then programme your new selection remembering to confirm it by
pressing the «Start/Pause» button
NB: If you change the programme without first
cancelling it, the machine displays:
This indicates that the new selection has not been
registered.
On the other hand, the current cycle is not cancelled and if you turn the
1
selector switch back to its original position, this cycle will resum.
• Throughout the cycle:
The following changes are possible without pressing the «Start/Pause»
6
button .
— You can change the temperature for the same type of textile.
NB:If the temperature achieved by the washing cycle is higher than
your new selection, heating the water stops immediately and the cycle
continues.
— You can alter the spin speed throughout the cycle.
— You can select «Drip Dry» and «Full drum stop» throughout the washing
phase.
• During the period before the cycle actually starts
have chosen to delay the time your washing starts):
Any kind of programme modification is accepted during a delayed start's
waiting period.
— You can alter the length of a delayed start throughout the waiting period
before the cycle effectively starts. To do this, press the (+) or (-) buttons
to select a new value.
NB:
- During this period, selecting a new time cancels out the previous
selection. The new period selected is accepted based on the last selection
made.
- If, during this time, you wish to completely cancel the «delayed start»,
press either the (+) button or the (-) button until the
the light comes on.
Then briefly press «Start/Pause»
The cycle will start immediately.
• When the cycle is over:
When the machine shows «StOP», you can programme a new cycle
without having to reset the selector
For this, all you have to do is turn the selector or press one of the buttons
2 3 4
, or .
The machine displays the time of the previously selected programme.
The machine is then ready to be reprogrammed.
22
6
is pressed.
6
.
(if you
light goes out and
6
.
1
to the position.
6
, you
.
5