Before Starting The Equipment - EINHELL GE-CR 30 Li Originalbetriebsanleitung

5. Before starting the equipment

Caution!
The equipment is supplied without batteries and
without a charger is allowed to be used only with
the lithium-ion batteries of the Power-X-Change
series!
Power-X-Change
•
18 V, 1.5 Ah, 5 lithium-ion cells
•
18 V, 2.0 Ah, 5 lithium-ion cells
•
18 V, 3.0 Ah, 10 lithium-ion cells
•
18 V, 4.0 Ah, 10 lithium-ion cells
•
18 V, 5.2 Ah, 10 lithium-ion cells
The lithium-ion batteries of the Power-X-Change
series are allowed to be charged only with the
Power-X charger.
Warning!
Always pull out the safety plug before making ad-
justments or carrying out maintenance, cleaning
and repair work on the equipment.
Assembly (Figs. 3a-3g)
•
Pull out the split pin (Fig. 3a/Item A) and re-
move the pin (Fig. 3a/Item B). Push the brake
shoe (Fig. 3b/Item 12) into the mount and fix it
in position with the pin and split pin previously
removed.
•
Undo the eight Philips screws (Fig. 3b/Pos.
C) with washers on both sides of the axle.
On both sides, push the transport wheel as
shown in Fig. 3c onto the axle and secure
with the Philips screws and washers (see Fig.
3c inset).
•
Press the wheel caps (Fig. 3d/Item 11) onto
the transport wheels.
•
Push the lower push bar as shown in Fig. 3e
onto the motor unit (Fig. 3e/Item 3) and se-
cure with the screws (Fig. 3e/Item 9) and the
star nuts (Fig. 3e/Item 8).
•
Push the upper push bar (Fig. 3f/Item 1) onto
the lower push bar (Fig. 3f/Item 2) and secure
with the screws (Fig. 3f/Item 9) and the star
nuts (Fig. 3f/Item 8).
•
Secure the cable to the push bars with 2
cable clips (Fig. 3g/Item 7).
Charging the battery (Fig. 4a/4b)
The equipment is supplied without batteries and
without a charger.
1. Take the battery pack out of the equipment.
To do so, press the pushlock button (Fig. 4a/
Anl_GE_CR_30_Li_SPK7.indb 20 Anl_GE_CR_30_Li_SPK7.indb 20
GB
Item C).
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the socket outlet. The green LED will then
begin to fl ash.
3. Insert the battery pack into the charger.
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts.
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
Installing the battery (Fig. 4c-4d)
Open the battery cover. This is done by pressing
the lock release (A) as shown in Fig. 4b and swin-
ging up the cover. Then connect the two batteries
into the mounts as shown in Fig. 4d and push
them forward until you hear the batteries engage.
Important!
Use only batteries which are charged to the same
level. Never combine full and half-full batteries.
Always charge the two batteries simultaneously.
The equipment's operating time depends on the
battery with the lower charge level. The two bat-
teries must always be fully charged before use.
Close the battery cover by swinging it down, and
make sure that it latches in place correctly.
Battery capacity indicator (Fig. 4a)
Press the switch for the battery capacity indicator
(Fig. 4a/Item A). The battery capacity indicator
(Fig. 4a/Item B) shows the charge status of the
battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
- 20 -
26.09.2016 11:10:09 26.09.2016 11:10:09