Operation - EINHELL GC-EL 3000 E Originalbetriebsanleitung

Pull the sleeve (Fig. 3f/Item A) to the top end of
the blower tube (Fig. 3f/Item 8) as shown in Fig.
3f. Make sure that it snaps in place correctly on
both sides.
5.2.1 Assembly in blower mode (Fig. 4a/4b)
Insert the blower tube (Fig. 4a/Item 8), which was
prepared in 5.1, into the mount (Fig. 4a/Item A)
on the motor housing. Make sure that it latches in
place correctly.
Fit the shoulder strap (Fig. 4b/Item 4) to the motor
housing as shown in Fig. 4b.
To dismantle, proceed in reverse order. To remove
the blower tube, press the button (Fig. 4a/Item B)
and pull off the blower tube.
5.2.2 Assembly in vacuum mode (Fig. 5a-5f)
Undo the star screw (Fig. 5a/Item A) and pull
open the cover (Fig. 5a/Item B). Attach the va-
cuum tube (Fig. 5b/Item 2), which was prepared
in 5.1, to the motor housing and snap it onto the
motor housing as shown in Fig. 5b. Now secure it
with the star screw (Fig. 5c/Item A).
Fit the shoulder strap (Fig. 5d/Item 4) to the motor
housing as shown in Fig. 5d.
Connect the catch bag (Fig. 5e/Item 7) to the
mount (Fig. 5e/Item A) on the motor housing.
Make sure that it latches in place correctly. Secu-
re the catch bag by the two hooks on the vacuum
tube as shown in Fig. 5f.
To remove the catch bag, press the button (Fig.
5e/Item B) and pull off the catch bag. To dismantle
the rest, proceed in reverse order.
Start up the equipment only when fully assem-
bled. Always inspect the power cable for damage
before starting up. The equipment may be used
only if the cable is in fl awless condition.
There are a number of safety switches for preven-
ting the unsafe operation of the equipment. Make
sure, therefore, that the following components are
correctly fastened, otherwise it will not be possib-
le to switch on the machine.
•
In blower mode: Blower tube (Fig. 4a/Item 8)
and cover (Fig. 5a/Item B).
•
In vacuum mode: Suction tube (Fig. 5b/Item
2) and catch bag (Fig. 5e/Item 7)
Anl_GC_EL_3000_E_SPK9.indb 21 Anl_GC_EL_3000_E_SPK9.indb 21
GB

6. Operation

6.1 Sizing the strap (Fig. 1)
Size the length of the carrying strap (4) so that the
vacuum tube just clears the ground. The guide
rollers (9) at the bottom end of the suction tube
will help you to maneuver the suction tube on the
ground.
6.2. Connecting the equipment to the power
supply and switching on (Fig. 6a/6b)
The equipment can be connected to any socket-
outlet (with 230 V AC) that is equipped with a
10A fuse or higher. The socket-outlet has to be
safeguarded by an earth-leakage circuit breaker
(e.l.c.b.).
The operating current must not exceed 30 mA.
•
Insert the equipment's plug into the power
cable coupling (extension).
•
Secure the power cable with the strain-relief
clip provided on the equipment as shown
(Fig. 6a).
•
To switch on, push the On/Off switch to the "I"
position
•
To switch off, push the On/Off switch to the
"O" position
6.3 Emptying the debris bag and pre-screen
(Fig. 1)
Empty the debris bag (7) in good time. When
the bag is heavily loaded with material, vacuum
power is considerably reduced. Deposit organic
refuse at a compost site.
•
Switch off the tool and pull out the plug.
•
Open the zipper on the debris bag (7) and
shake out the material.
•
Close the zip on the debris bag (7) again.
6.4 Speed control (Fig. 6b)
The device is fi tted with an electronic speed con-
troller. To use it, turn the speed controller (Fig. 6b/
Item 10) to the desired position. Use the device
only with the speed which is actually required and
do not let it run at a speed which is faster than
necessary.
- 21 -
20.03.2018 11:18:13 20.03.2018 11:18:13