Operation - EINHELL GE-CL 36/230 Li E Originalbetriebsanleitung

5.6 Charging the battery (Fig. 7-8)
1. Take the battery pack out of the equipment.
To do so, press the pushlock button (Fig. 8/
Item C).
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the socket outlet. The green LED will then
begin to fl ash.
3. Insert the battery pack into the charger.
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The rechargeable battery can become a little
warm during the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charger
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
Battery capacity indicator (Fig. 8)
Press the button for the battery capacity indicator
(Item A). The battery capacity indicator (Item B)
shows the charge status of the battery using 3
LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
Anl_GE_CL_36_230_Li_E_Solo_SPK9.indb 22 Anl_GE_CL_36_230_Li_E_Solo_SPK9.indb 22
GB
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs fl ash:
The rechargeable battery has undergone ex-
haustive discharge and is defective. Do not use or
charge a defective rechargeable battery.

6. Operation

Danger!
Start up the equipment only when fully assem-
bled.
6.1 Sizing the strap
Slip the harness over your shoulder and adjust
the length of the harness so that you can handle
the equipment comfortably.
Caution: Wear the harness in such a way that
the snap fastener is always close to hand. In
an emergency you can always remove the
equipment quickly by opening the snap fas-
tener (Fig. 9 / Item B).
6.2 Switching on the equipment (Fig. 10)
•
To switch on, push the On/Off (5) switch to
the "I" position
•
To switch off, push the On/Off switch to the "0"
position
6.3 Mode of operation
Caution! Search the surface for concealed ob-
jects (e.g. small animals or hard foreign bodies)
before starting to use the equipment.
6.3.1 Blowing foliage
Caution!
If you point the air fl ow towards other people, ani-
mals or objects (e.g. windows), this could cause
injuries and damage.
•
Point the air flow away from yourself.
•
Never point the air flow towards other people,
animals or objects.
•
Do not blow away any hard objects such as
stones or twigs.
•
Fit the prepared blower tube and harness
(see section 5.2) to the motor housing.
•
Check that all the components are correctly
fastened (see section 5.4).
•
Position the blower tube just above the
ground and adjust the length of the strap to
your requirements (see section 6.1).
•
Turn on the equipment (see section 6.2).
- 22 -
17.12.2019 14:38:10 17.12.2019 14:38:10