Herunterladen Inhalt Inhalt Diese Seite drucken

Installing The Stove; Adjustable Legs (Excluding The Models M1/M2/ M3/M3 Sl/Linear 16/16); Connecting The Stove To A Masonry Flue; Montage Des Ofens - Harvia M2 Bedienungsanleitung

Vorschau ausblenden Andere Handbücher für M2:
Inhaltsverzeichnis

Werbung

EN

3.2. Installing the Stove

3.2.1. Adjustable Legs (excluding the models M1/
M2/M3/M3 SL/Linear 16/16)
The adjustable legs enable the stove to be installed
firmly on an inclined floor. The adjustable range is
0–30 mm. Unscrew the adjustable feet to an extent
that allows them to be adjusted using a wrench
(17 mm) when the stove is in position.
The adjustable feet could scratch the floor
surface if the stove is moved on the floor.

3.2.2. Connecting the Stove to a Masonry Flue

Make an opening in the fireproof wall for the flue
connection. Notice that the opening has to be at the
correct height, if you intend to use, for instance, a
protective bedding. The hole should be slightly larger
than the flue connecting pipe. A suitable gap around
the connection pipe is ca. 10 mm. It is advisable to
round off the inner corners of the flue opening to
ensure that the combustion gases can flow freely
to the flue. Additional accessories are available to
make the installation easier ( 3.4.).
M1, M2, M3/SL, 20 Pro/SL, 20 ES Pro/S, 20
Boiler/SL, Classic 140/220/280, Premium/VS, 20
RS/LS Pro/ Linear 16/22, 16/22: Connecting the
stove to a masonry flue via the rear connection
opening (figure 9)
1. Bend the cover hatch downwards (M1/M2/M3,
Classic 140/220/280, Premium/Premium VS,
Linear 16, 16 only). Attach the flue connection
pipe to the rear connection opening. Ensure
that the pipe fits tightly in place.
2. Push the stove into place. Do not block the flue
by pushing the flue connection pipe too far into
the flue. If necessary, shorten the pipe.
3. Seal the flue connection pipe to the opening
in the fireproof wall, for example, by using
fireproof mineral wool. Make sure that the flue
connection is tightly sealed. Add more fireproof
mineral wool if necessary.
Figure 9.
Connecting the stove to a masonry flue via the rear connection opening (all dimensions in millimeters)
Abbildung 9. Anschluss des Ofens an einen gemauerten Rauchfang über die hintere Anschlussöffnung (alle
Abmessungen in Millimetern)
14
DE

3.2. Montage des Ofens

3.2.1. Verstellbare Füße des Ofens (Außer bei Mo-
dellen M1/M2/M3/M3 SL/Linear 16/16)
Die verstellbaren Füße dienen zur sicheren Installation
auf schiefer Grundfläche. Regelbereich 0–30 mm. Die
verstellbaren Füße sollten bis zu einem Ausmaß gelöst
werden, das es ermöglicht, sie mit einem Gabelschlüs-
sel (17 mm) einzustellen, wenn der Ofen an seinem
Platz steht.
Die verstellbaren Füße können die Bodenober-
fläche zerkratzen, wenn der Ofen auf dem
Boden bewegt wird.
3.2.2. Anschluss des Ofens an einen gemauerten
Rauchfang
Stellen Sie in der Brandmauer eine Öffnung für den
Abzugsanschluss her. Beachten Sie, falls Sie z.B.
eine Schutzplatte anzubringen gedenken, dass sich
die Öffnung auf der richtigen Höhe befinden muss.
Das Loch sollte etwas größer sein als der Durchmesser
des Abzugsanschlussrohres. Eine Dichtungslücke von
etwa 10 mm um das Rohr herum ist angemessen. Es
ist ratsam, die inneren Ecken der Rauchfangsöffnung
abzurunden, damit die Rauchgase in den Rauchfang
frei abziehen können. Zur einfacheren Montage steht
zusätzliches Zubehör zur Verfügung ( 3.4.).
M1, M2, M3/SL, 20 Pro/SL, 20 ES Pro/S, 20 Boiler/
SL, Classic 140/220/280, Premium/VS, 20 RS/LS
Pro/ Linear 16/22, 16/22: Anschluss des Ofens an
einen gemauerten Rauchfang über die hintere An-
schlussöffnung (Abbildung 9)
1. Biegen Sie den Deckel nach unten (nur M1/M2/
M3, Classic 140/220/280, Premium/Premium
VS, Linear 16, 16). Bringen Sie das Abzugsan-
schlussrohr an die hintere Anschlussöffnung an.
Das Rohr muss fest an seinem Platz sitzen.
2. Schieben Sie den Ofen an seine Position. Schie-
ben Sie das Abzugsanschlussrohr nicht zu weit
in den Rauchfang hinein. Kürzen Sie das Rohr,
falls notwendig.
3. Dichten Sie das Abzugsanschlussrohr in der
Öffnung der feuerfesten Wand ab, z.B. mit
feuerfester Mineralwolle. Der Abzugsanschluss
muss absolut dicht sein. Fügen Sie gegebenen-
falls mehr Mineralwolle hinzu.
1
3
2

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis