Audio Settings - Kenwood KDC-BT35U Bedienungsanleitung

AUDIO SETTINGS

While listening to any source...
1
Press the volume knob to enter [FUNCTION].
2
Turn the volume knob to select [AUDIO CONTROL], then press the
knob.
3
Turn the volume knob to make a selection (see the following table),
then press the knob.
4 Repeat step 3 until the desired item is selected or activated.
5 Press and hold to exit.
To return to the previous setting item, press
SUB-W LEVEL –15 to +15 (0)
BASS LEVEL –8 to +8 (+6)
MID LEVEL –8 to +8 (+5)
TRE LEVEL –8 to +8 (0)
EQ PRO
BASS ADJUST BASS CTR FRQ
BASS LEVEL
BASS Q FACTOR
BASS EXTEND
MID ADJUST MID CTR FRQ
MID LEVEL
MID Q FACTOR
TRE ADJUST TRE CTR FRQ
TRE LEVEL
14
.
Default: XX
Adjusts the subwoofer output level.
Adjusts the level to memorize for each source.
(Before making an adjustment, select the source
you want to adjust.)
60/ 80/ 100/ 200: Selects the center frequency.
–8 to +8 (+6): Adjusts the level.
1.00/ 1.25/ 1.50/ 2.00: Adjusts the quality factor.
ON: Turns on the extended bass. ; OFF: Cancels.
0.5K/ 1.0K/ 1.5K/ 2.5K: Selects the center
frequency.
–8 to +8 (+5): Adjusts the level.
0.75/ 1.00/ 1.25: Adjusts the quality factor.
10.0K/ 12.5K/ 15.0K/ 17.5K: Selects the center
frequency.
–8 to +8 (0): Adjusts the level.
PRESET EQ DRIVE EQ/ TOP40/ POWERFUL/ ROCK/ POPS/ EASY/ JAZZ/
NATURAL/ USER: Selects a preset equalizer suitable to the music
genre. (Select [USER] to use the customized settings.)
[DRIVE EQ] is a preset equalizer that reduces noise outside the car
or running noise of the tyres.
BASS BOOST LV1/ LV2/ LV3: Selects your preferred bass boost level. ;
OFF: Cancels.
LOUDNESS LV1/ LV2: Selects your preferred low and high frequencies
boost to produce a well-balanced sound at a low volume level. ;
OFF: Cancels.
SUBWOOFER SET ON: Turns on the subwoofer output. ; OFF: Cancels.
LPF SUBWOOFER THROUGH: All signals are sent to the subwoofer. ; 85HZ/ 120HZ/
160HZ: Audio signals with frequencies lower than 85 Hz/ 120 Hz/
160 Hz are sent to the subwoofer.
SUB-W PHASE REVERSE (180°)/ NORMAL (0°): Selects the phase of the
subwoofer output to be in line with the speaker output for
optimum performance. (Selectable only if a setting other than
[THROUGH] is selected for [LPF SUBWOOFER].)
FADER R15 to F15 (0): Adjusts the rear and front speaker output balance.
BALANCE L15 to R15 (0): Adjusts the left and right speaker output balance.
VOLUME OFFSET For AUX: –8 to +8 (0) ; For other sources: –8 to 0: Presets the
volume adjustment level of each source. (Before adjustment,
select the source you want to adjust.)
SOUND RECNSTR ON: Creates realistic sound by compensating the high-frequency
(Sound reconstruction) components and restoring the rise-time of the waveform that are
lost in audio data compression. ; OFF: Cancels.
• [SUB-W LEVEL]/ [SUBWOOFER SET]/ [LPF SUBWOOFER]/ [SUB-W PHASE] is
selectable only if [SWITCH PREOUT] is set to [SUB-W]. ( 4)
• [SUB-W LEVEL]/ [LPF SUBWOOFER]/ [SUB-W PHASE] is selectable only if
[SUBWOOFER SET] is set to [ON].