testo 560 Bedienungsanleitung Seite 40

5. Operation
C C l l i i e e n n t t : :
F F R R E E E E F F R R O O M M : :
P P l l a a n n t t : :
F F R R E E E E F F R R O O M M : :
S S t t o o r r e e o o n n
E E n n t t e e r r ? ?
P P r r e e l l - - 0 0 . . 1 1
S S a a v v e e - - 4 4 9 9 . . 0 0
S S a a v v i i n n g g O O K K
K K : : 0 0 0 0 8 8 / / A A : : 0 0 2 2
I I n n t t e e r r v v a a l l i i n n
M M i i n n u u t t e e s s : :
I I n n t t e e r r v v a a l l i i n n
M M i i n n u u t t e e s s : :
L L o o g g g g i i n n g g ? ?
K K : : 0 0 0 0 8 8 / / A A : : 0 0 1 1
P P r r e e l l - - 0 0 . . 1 1
L L O O G G G G - - 4 4 9 9 . . 0 0
L L o o g g g g i i n n g g
c c o o m m p p l l e e t t e e d d ? ? ( ( E E n n t t e e r r ) )
16
3 Select the desired customer number with
0 0 0 0 1 1
F F R R E E E E F F R R O O M M
0 0 0 0 5 5
has been stored, for your information.
4 Confirm selection with
5 Select the desired plant number with
0 0 1 1
F F R R E E E E F F R R O O M M
0 0 2 2
has been stored, for your information.
6 Confirm selection with
7 Start logging with
1 1 8 8 . . 4 4
- The unit changes to the vacuum measurement screen and
- - 4 4 2 2 . . 4 4
S S a a v v e e
procedure.
Logging individual measured values
Store the current measured values with
S S a a v v i i n n g g O O K K
-
measured values have been stored are displayed for 2
seconds.
Saving measured value series
The battery capacity should be checked or if necessary the
power supply unit connected for longer logs. If the battery is
expended during logging, the unit switches off automatically.
The measurements made up to the shut-off are not lost.
Hold
remaining battery capacity.
Carry out the steps 1 to 6 in the "Starting the logging" section
(see above), then continue as follows:
7 Select the
S S e e c c o o n n d d s s
1 1 0 0
terval with
- The client/plant number for which the measured data will be
3 3 0 0
stored are displayed.
9 Start the series measurement with
L L O O G G G G
-
alternately. The measured value series is stored.
1 1 8 8 . . 4 4
10 Terminate logging with
4 4 2 2 . . 4 4
11 Terminate logging with
shows the first client number for which no data
.
shows the first plant number for which no data
.
.
flashes. No reading has been saved prior to this
and the customer / plant number for which the
depressed for longer than 2 seconds to display the
I I n n t t e e r r v v a a l l i i n n M M i i n n u u t t e e s s
with or .
or and confirm the selection with
and the remaining memory capacity display flash
.
or continue with
or .
or .
.
I I n n t t e e r r v v a a l l i i n n
or
.
Save.
.