Inhaltsverzeichnis
Werbung
20 cm
1.5 m
1. USB cable
Connect the USB portable audio
12. Note:
player or USB memory (sold
Depending on the kind of vehicle,
separately).
the function of 3* and 5* may be
different. In this case, be sure to
9. Front output
connect 2* to 5* and 4* to 3*.
1*
2. Antenna jack
3*
2*
3. Subwoofer output
4. AUX jack (3.5 ø)
5*
4*
Use a stereo mini plug cable
to connect with auxiliary
13. Connect leads of the same
color to each other.
equipment.
5. Wired remote input
Hard-wired remote control
14. Cap (1*)
adaptor can be connected
Do not remove cap
(sold separately).
if this terminal is
15. Fuse (10 A)
not in use.
16. Yellow (3*)
17. Yellow (2*)
Back-up (or
Connect to the constant
accessory)
12 V supply terminal.
22. Fuse resistor
18. Red (5*)
19. Red (4*)
Accessory
Connect to terminal controlled
(or back-up)
by ignition switch (12 V DC).
22. Fuse resistor
20. Orange/white
Connect to lighting switch terminal.
21. Black (chassis ground)
Connect to a clean, paint-free metal location.
23. ISO connector
24. Yellow/black
Note:
If you use an equipment with Mute
In some vehicles, the ISO connector may
function, wire this lead to the Audio
be divided into two. In this case, be sure
Mute lead on that equipment. If not,
to connect to both connectors.
keep the Audio Mute lead free of any
connections.
16 cm
8. Rear output
30. Power amp
(sold separately)
7. This product
6. IP-BUS input (Blue)
29. Connect with RCA cables
(sold separately)
10. IP-BUS cable
11. Multi-CD player
(sold separately)
31. System remote control
25. Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
+
+
32. Front speaker
≠
≠
33. Left
26. Blue/white (7*)
Connect to auto-antenna relay control
terminal (max. 300 mA 12 V DC).
+
+
35. Rear speaker
27. Blue/white (6*)
≠
≠
The pin position of the ISO connector will
differ depends on the type of vehicle. Connect
6* and 7* when Pin 5 is an antenna control
type. In another type of vehicle, never connect
+
+
6* and 7*.
36. Subwoofer
≠
≠
37. Perform these connections when
28. Speaker leads
using the optional amplifier.
Front left +
White:
White/black: Front left ≠
Front right +
Gray:
38. Notes:
Gray/black: Front right ≠
• Change the initial setting of this unit (refer to the Operation
Green:
Rear left + or subwoofer +
Manual). The subwoofer output of this unit is monaural.
• When using a subwoofer of 70 W (2 Ω) , be sure to connect
Green/black: Rear left ≠ or subwoofer ≠
Rear right + or subwoofer +
Violet:
with Violet and Violet/black leads of this unit. Do not connect
Violet/black: Rear right ≠ or subwoofer ≠
anything with Green and Green/black leads.
Connecting the Units
30. Power amp
Note:
(sold separately)
•
When this unit is installed in a vehicle without
ACC (accessory) position on the ignition switch,
red cable must be wired to the terminal that can
30. Power amp
detect the operation of the ignition key.
(sold separately)
Otherwise, battery drain may result.
ACC position
No ACC position
•
Use this unit in other than the following condi-
tions could result in fire or malfunction.
— Vehicles with a 12-volt battery and negative
grounding.
— Speakers with 50 W (output value) and 4 ohm
to 8 ohm (impedance value).
•
To prevent short-circuit, overheating or malfunc-
tion, be sure to follow the directions below.
— Disconnect the negative terminal of the bat-
tery before installation.
— Secure the wiring with cable clamps or adhe-
sive tape. To protect the wiring, wrap adhe-
32. Front speaker
sive tape around them where they lie against
metal parts.
34. Right
— Place all cables away from moving parts,
such as gear shift and seat rails.
— Place all cables away from hot places, such as
near the heater outlet.
35. Rear speaker
— Do not pass the yellow cable through a hole
into the engine compartment to connect to a
battery.
— Cover any disconnected cable connectors
with insulating tape.
— Do not shorten any cables.
36. Subwoofer
— Never cut the insulation of the power cable of
this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.
— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly
to ground.
— Never band together multiple speaker's nega-
tive cables.
•
Control signal is output through blue/white cable
Connection Diagram
when this unit is powered on. Connect it to an
external power amp's system remote control or
1. USB cable
the vehicle's auto-antenna relay control terminal
Connect the USB portable audio player or USB
(max. 300 mA, 12 V DC). If the vehicle is
memory (sold separately).
equipped with a glass antenna, connect it to the
2. Antenna jack
antenna booster power supply terminal.
3. Subwoofer output
•
Never connect blue/white cable to external power
4. AUX jack (3.5 ø)
amp's power terminal. Also, never connect it to
Use a stereo mini plug cable to connect with
the power terminal of the auto antenna.
auxiliary equipment.
Otherwise, battery drain or malfunction may
5. Wired remote input
result.
Hard-wired remote control adaptor can be con-
•
IP-BUS connectors are color-coded. Be sure to
nected (sold separately).
connect connectors of the same color.
6. IP-BUS input (Blue)
•
Black cable is ground. This cable and other prod-
7. This product
uct's ground cable (especially, high-current prod-
8. Rear output
ucts such as power amp) must be wired separate-
9. Front output
ly. Otherwise, fire or malfunction may result if
10. IP-BUS cable
they are accidentally detached.
11. Multi-CD player (sold separately)
•
Cord function may differ according to the
12. Note:
product, even if cord color is the same. When
Depending on the kind of vehicle, the function of
connecting this system, be sure to check all
3* and 5* may be different. In this case, be sure
manuals and connect cords correctly.
to connect 2* to 5* and 4* to 3*.
13. Connect leads of the same color to each other.
14. Cap (1*)
Do not remove cap if this terminal is not in use.
15. Fuse (10 A)
16. Yellow (3*)
Back-up (or accessory)
17. Yellow (2*)
Connect to the constant 12 V supply terminal.
18. Red (5*)
Accessory (or back-up)
19. Red (4*)
Connect to terminal controlled by ignition switch
(12 V DC).
20. Orange/white
Connect to lighting switch terminal.
21. Black (chassis ground)
Connect to a clean, paint-free metal location.
22. Fuse resistor
23. ISO connector
Note:
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to connect
to both connectors.
ENGLISH
24. Yellow/black
If you use an equipment with Mute function,
wire this lead to the Audio Mute lead on that
equipment. If not, keep the Audio Mute lead free
of any connections.
25. Blue/white
Connect to system control terminal of the power
amp (max. 300 mA 12 V DC).
26. Blue/white (7*)
Connect to auto-antenna relay control terminal
(max. 300 mA 12 V DC).
27. Blue/white (6*)
The pin position of the ISO connector will differ
depends on the type of vehicle. Connect 6* and
7* when Pin 5 is an antenna control type. In
another type of vehicle, never connect 6* and 7*.
28. Speaker leads
White:
Front left +
White/black: Front left ≠
Front right +
Gray:
Gray/black: Front right ≠
Rear left + or subwoofer +
Green:
Green/black: Rear left ≠ or subwoofer ≠
Violet:
Rear right + or subwoofer +
Violet/black: Rear right ≠ or subwoofer ≠
29. Connect with RCA cables (sold separately)
30. Power amp (sold separately)
31. System remote control
32. Front Speaker
33. Left
34. Right
35. Rear Speaker
36. Subwoofer
37. Perform these connections when using the
optional amplifier.
38. Notes:
• Change the initial setting of this unit (refer to
the Operation Manual). The subwoofer output
of this unit is monaural.
• When using a subwoofer of 70 W (2 Ω), be
sure to connect with Violet and Violet/black
leads of this unit. Do not connect anything with
Green and Green/black leads.
Werbung
Inhaltsverzeichnis
