Connecting The Units - Pioneer DEH-P5800MP Installationsanleitung

8. Multi-CD player
Note:
(sold separately)
Depending on the kind of vehicle, the function
5. IP-BUS cable
of 3* and 5* may be different. In this case, be
sure to connect 2* to 5* and 4* to 3*.
1. This product
1*
3* 2*
2. Subwoofer output or
non fading output
4. Antenna jack
5* 4*
3. Front output
11. Connect leads of the same
color to each other .
12. Cap (1*)
When not using this terminal,
do not remove the cap.
13. Yellow (3*) 14. Yellow (2*)
Back-up To terminal always supplied
(or accessory) with power regardless of
ignition switch position.
15. Red (5*) 16. Red (4*)
Accessory To electric terminal controlled
(or back-up) by ignition switch (12 V DC)
ON/OFF.
17. Black (ground)
To vehicle (metal) body.
18. ISO connector
Note:
19. Yellow/black
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to If you use a cellular telephone, connect it via the
connect to both connectors. Audio Mute lead on the cellular telephone. If not,
keep the Audio Mute lead free of any connections.
21. Connecting cords with RCA pin plugs
(sold separately)
6. IP-BUS input (Blue)
9. Fuse 7. Jack for the Wired Remote Control
Please see the Instruction Manual for the
Wired Remote Control (sold separately).
23.Blue/white
To system control terminal of the power
amp (max. 300 mA 12 V DC).
24. System remote control
25. Blue/white (7*)
To Auto-antenna relay control terminal
(max. 300 mA 12 V DC).
26. Blue/white (6*)
27. The pin position of the ISO connector will differ
depends on the type of vehicle. Connect 6* and 7*
when Pin 5 is an antenna control type. In another
type of vehicle, never connect 6* and 7*.
28. Front Speaker
28. Front Speaker
29. Left
31. Subwoofer 31. Subwoofer
20. Speaker leads
White : Front left + 32. Perform these connections when using
the optional amplifier.
White/black : Front left ≠
Gray : Front right +
Gray/black : Front right ≠
33. Note:
Green : Rear left + or Subwoofer +
Change the initial setting of this unit
Green/black : Rear left or Subwoofer
≠ ≠
(refer to the operational Manual).
Violet : Rear right + or Subwoofer +
The subwoofer outputof the unit is
Violet/black : Rear right ≠ or Subwoofer ≠
monaural.

Connecting the Units

Note:
• This unit is for vehicles with a 12-volt battery
and negative grounding. Before installing it in a
recreational vehicle, truck, or bus, check the bat-
22. Power amp
tery voltage.
(sold separately)
• To avoid shorts in the electrical system, be sure
≠ battery cable before begin-
to disconnect the
22. Power amp ning installation.
(sold separately)
• Refer to the owner's manual for details on con-
necting the power amp and other units, then
make connections correctly.
• Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.
• Route and secure all wiring so it cannot touch
any moving parts, such as the gear shift, hand-
brake and seat rails. Do not route wiring in
places that get hot, such as near the heater outlet.
If the insulation of the wiring melts or gets torn,
there is a danger of the wiring short-circuiting to
the vehicle body.
• Don't pass the yellow lead through a hole into
the engine compartment to connect to the battery.
This will damage the lead insulation and cause a
very dangerous short.
• Do not shorten any leads. If you do, the protec-
tion circuit may fail to work when it should.
• Never feed power to other equipment by cutting
the insulation of the power supply lead of the
unit and tapping into the lead. The current capac-
ity of the lead will be exceeded, causing over-
heating.
• When replacing the fuse, be sure to only use a
fuse of the rating prescribed on this product.
• Since a unique BPTL circuit is employed, never
wire so the speaker leads are directly grounded
30. Right
or the left and right ≠ speaker leads are com-
mon.
• Speakers connected to this unit must be high-
power with minimum rating of 50 W and imped-
ance of 4 to 8 ohms. Connecting speakers with
output and/or impedance values other than those
noted here may result in the speakers
catching fire, emitting smoke or becoming dam-
aged.
• When this product's source is switched ON, a
control signal is output through the blue/white
lead. Connect to an external power amp's system
remote control or the car's Auto-antenna relay
control terminal (max. 300 mA 12 V DC). If the
car features a glass antenna, connect to the anten-
na booster power supply terminal.
Connection Diagram
• When an external power amp is being used with
this system, be sure not to connect the blue/white 1. This product
lead to the amp's power terminal. Likewise, do
2. Subwoofer or non fading output
not connect the blue/white lead to the power ter-
3. Front output
minal of the auto-antenna. Such connection could
4. Antenna jack
cause excessive current drain and malfunction.
5. IP-BUS cable
• To avoid a short-circuit, cover the disconnected
6. IP-BUS input (Blue)
lead with insulating tape. Insulate the unused
7. Jack for the Wired Remote Control
speaker leads without fail. There is a possibility
Please see the Instruction Manual for the Wired
of a short-circuit if the leads are not insulated.
Remote Control (sold separately).
• To prevent incorrect connection, the input side of
8. Multi-CD player (sold separately)
the IP-BUS connector is blue, and the output side
is black. Connect the connectors of the same col- 9. Fuse
ors correctly.
10. Note:
• If this unit is installed in a vehicle that does not Depending on the kind of vehicle, the function of
have an ACC (accessory) position on the ignition 3* and 5* may be different. In this case, be sure
switch, the red lead of the unit should be con- to connect 2* to 5* and 4* to 3*.
nected to a terminal coupled with ignition switch
11. Connect leads of the same color to each other.
ON/OFF operations. If this is not done, the vehi-
12. Cap (1*)
cle battery may be drained when you are away
When not using this terminal, do not remove the
from the vehicle for several hours.
cap.
13. Yellow (3*)
Back-up (or accessory)
14. Yellow (2*)
To terminal always supplied with power regard-
less of ignition switch position.
15. Red (5*)
Accessory (or back-up)
16. Red (4*)
To electric terminal controlled by ignition switch
(12 V DC) ON/OFF.
No ACC position
ACC position
17. Black (ground)
• The black lead is ground. Please ground this lead
To vehicle (metal) body.
separately from the ground of high-current prod-
18. ISO connector
ucts such as power amps.
Note:
If you ground the products together and the
In some vehicles, the ISO connector may be
ground becomes detached, there is a risk of dam-
divided into two. In this case, be sure to connect
age to the products or fire.
to both connectors.
19. Yellow/black
• Cords for this product and those for other prod- If you use a cellular telephone, connect it via the
ucts may be different colors even if they have Audio Mute lead on the cellular telephone. If not,
the same function. When connecting this prod- keep the Audio Mute lead free of any connec-
uct to another product, refer to the supplied tions.
manuals of both products and connect cords that
have the same function.
<ENGLISH>
20. Speaker leads
: Front left +
White
White/black : Front left ≠
Gray : Front right +
Gray/black : Front right ≠
: Rear left +
Green
Green/black : Rear left ≠
: Rear right +
Violet
Violet/black : Rear right ≠
21. Connecting cords with RCA pin plugs (sold
separately)
22. Power amp (sold separately)
23. Blue/white
To system control terminal of the power amp
(max. 300 mA 12 V DC).
24. System remote control
25. Blue/white (7*)
To Auto-antenna relay control terminal
(max. 300 mA 12 V DC).
26. Blue/white (6*)
27.The pin position of the ISO connector will differ
depends on the type of vehicle. Connect 6* and
7* when Pin 5 is an antenna control type. In
another type of vehicle, never connect 6* and 7*.
28. Front Speaker
29. Left
30. Right
31. Subwoofer
32. Perform these connections when using the
optional amplifier.
33. Note:
Change the initial setting of this unit (refer to the
Operational Manual). Subwoofer output of this
unit is monaural.