Herunterladen Inhalt Inhalt Diese Seite drucken

Connections; Output Mode (Sxga, Xga Or Svga); And Vertical Frequency (75 Or 60Hz); Pal/Ntsc Video Outputs - WolfVision VZ-C10 Bedienungsanleitung

Vorschau ausblenden Andere Handbücher für VZ-C10:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

CONNECTIONS

VD
S/HD
IR SENSOR
Video
37
38
#26 Main POWER switch
#27 FUSE (see page 13)
#28 POWER connection
#29 DVI output (see page 15)
#30 USB port (see page 10)
#31 SERIAL port for external remote controlling
#32 PREVIEW RGBHV output for control monitor

OUTPUT MODE (SXGA, XGA or SVGA)

and VERTICAL FREQUENCY (75 or 60Hz)

The RGBHV-, Preview- and DVI-outputs (#32, 33, 35 and 29) can output a signal in the following formats:
- SXGA (1280x1024 pixel) at 60Hz
- XGA (1024x768 pixel) at 75Hz
- XGA (1024x768 pixel) at 60Hz (default setting if auto resolution does not work)
- SVGA (800x600 pixel) at 75Hz
- SVGA (800x600 pixel) at 60Hz
The "Auto resolution" function is activated by default. In this mode the Visualizer constantly checks which devices
are connected to the RGBHV (#32, 33) and DVI output (#29) and automatically sets the optimal output mode that
fits best for all connected units. Please note that the Visualizer can not check the possible resolution, if the
connected units or the cables* are not "Plug and Play" compatible. If the Visualizer can not detect the resolution of
ALL connected units, the output-mode is set to the default of XGA (1024x768) at 60Hz.
(* Cables with plug and play compatibility must have a 15-pin plug on both ends with all pins connected, pin 9 is not used)
.
In order to achieve the best picture quality you should set the outputs of the Visualizer to match the native resolution
of your display unit (e.g. LCD or DLP projector or monitor) - see page 15.
Important: What matters is the native resolution of the projector or monitor, not the maximum resolution that it can
display (in compressed mode). The native resolution is the actual number of pixels of the built in LCD display or
DLP chip of a projector or monitor. Most LCD or DLP projectors can also display higher resolutions than their native
resolution, but only in compressed mode and with inferior picture quality.
Do NOT set the output of the Visualizer to a higher standard than the native resolution of your display unit!
For LCD- or DLP-projectors, LCD-monitors and video-conferencing units a setting with 60Hz is recommended. For
CRT-based monitors or projectors use a setting with 75Hz, because these units may show a slight image flickering
with 60Hz.
Please note that images from the EXTERNAL INPUT (#34) are not output at the DVI output (#29)!
PAL / NTSC VIDEO OUTPUTS
The Y/C (S-video) (#36) and Composite (#37) video outputs can be switched between PAL and NTSC in the
units
on-screen menu
(see page 15).
Please note, that the picture quality of the Y/C (S-video) (#36) output is BETTER than the quality of the
Composite (#37) video output. However t
the picture quality of the data outputs
video system and because of the fact that this is just a converted Progressive Scan signal and not an original
video signal.
Please note that images from the EXTERNAL INPUT (#34) are not output at the Y/C (S-video) and Composite
output!
The Y/C (S-video) and Composite Video outputs are intended for control monitors, they output a signal even if
the picture is switched off.
B
G
35
Y/C
34
EXTERN IN
36
he picture quality of both video outputs is BY FAR NOT AS GOOD as
(#33, 32, 35 and 29). This is because of the limitations of the PAL/NTSC
R
SXGA
33
USB
32
PREVIEW
30
#33 RGBHV output 15-pin (switchable)
#34 EXTERNAL Input for Computers (see page 11)
#35 RGBHV output BNC connectors (switchable)
(Sync-settings see page 11)
#36 PAL/NTSC Y/C (S-Video) output (see below)
#37 PAL/NTSC Composite video output (see below)
#38 Input for additional INFRARED SENSOR
(see page 12)
5
28
SERIAL
31
29
DVI

IMPORTANT

26
27

Werbung

Kapitel

Inhaltsverzeichnis
loading

Inhaltsverzeichnis