On-Screen Menu / Camera Menu; Reset Of On-Screen Menu Settings / Menu-Presets; Switching To Negative, Negative/Blue And Black/White - WolfVision VZ-C10 Bedienungsanleitung

The following chapters are for experienced users only!
ON-SCREEN MENU / CAMERA-MENU
For standard use of the WolfVision Visualizer it is NOT necessary to enter the Visualizer's menu and change
settings. Inexperienced users should not try to make any adjustments there.
MEMORY
22
HELP
21
The functions of the o n-screen menu
This is because the help texts are an integrated part of the Visualizer's software (firmware) and always refer to the
firmware version which is currently loaded on your Visualizer.
RESET OF ON-SCREEN-MENU SETTINGS / PRESETS
The settings in the on-screen menu
Menu. The on-screen menu also offers the possibility to store three different menu settings as menu-presets.

SWITCHING TO NEGATIVE, NEGATIVE/BLUE and BLACK/WHITE

The output image of the Visualizer can be switched from positive to negative in the on-screen menu. In addition the
background of a negative image can be switched to blue for better readability of text. You can also switch between
color and black/white in the
TIP: If the negative, negative/blue or black/white images are often required, you can assign this function to one of
the Preset keys (#14) in the
DVI-I PORT
Pin 8
Pin 1
Pin 9
Pin 17
Pin 24
DVI-I ports are divided into a digital and
an analog section. Please note that the
image of the External input (#32) is only
output at the analog DVI section!
SERIAL PORT / SERIAL PROTOCOL
1 2 3 4 5
9-pin D-Sub connector
on unit, male, front side
6 7 8 9
Pins: 2:RX, 3:TX, 5:GND
FIRMWARE UPGRADES
The software (firmware) of your Visualizer (including the o
version. First download the latest firmware and WolfVision's firmware update utility program from Wolfvision's
internet homepage at www.wolfvision.com/support. Then connect the serial port of the Visualizer with
the serial port of your computer using a crossed serial RS232 cable and run the firmware update utility program.
More details on the firmware updates can be found on WolfVision's internet homepage.
For entering the Visualizer's menu press the Menu key (#19) for 1 second.
(The menu does not appear when the menu key is
prevent that inexperienced users enter the menu by mistake).
When the menu appears on the screen, settings of the Visualizer's basic functions and
the built-in camera can be made using the 4 select keys (#22).
If you require more information on a function in the on-screen menu just set the cursor
in the respective line and press the HELP key (#21). A detailed description of this
function appears on the screen.
are described in the help menu of the Visualizer and not in this user manual.
can be set back to the factory defaults. "Reset" is an item in the on-screen
on-screen menu .
on-screen menu .
1 - T.M.D.S. Data2-
2 - T.M.D.S. Data2+
3 - T.M.D.S. Data2/4 Shield
4 - T.M.D.S. Data4- (not used)
5 - T.M.D.S. Data4+(not used)
6 - DDC Clock
7 - DDC Data
8 - Analog Vertical Sync
C1 - Analog Red
C4 - Analog Horizontal Sync
A detailed description of the serial protocol (including status
report and position setting) is available on request from your
WolfVision dealer or can be downloaded from our website:
http://www.wolfvision.com/support.
only
9 - T.M.D.S. Data1-
10 - T.M.D.S. Data1+
11 - T.M.D.S. Data1/3 Shield
12 - T.M.D.S. Data3- (not used)
13 - T.M.D.S. Data3+ (not used)
14 - +5V Power
15 - Ground (return for +5V,
HSync and VSync)
16 - Hot Plug Detect
C2 - Analog Green
C5 - Analog Ground
(analog R, G & B return)
n-screen HELP ) can easily be upgraded to the latest
15
MENU
pressed quickly. This is to
17 - T.M.D.S. Data0-
18 - T.M.D.S. Data0+
19 - T.M.D.S. Data0/5 Shield
20 - T.M.D.S. Data5- (not used)
21 - T.M.D.S. Data5+ (not used)
22 - T.M.D.S. Clock+
23 - T.M.D.S. Clock-
24 - Analog Vertical Sync
C3 - Analog Blue
19