Locating The End Of The Recorded Portion (End Search); Setting The Recording Mode - Sony DTC-A6 Bedienungsanleitung

Recording Operations
If the level exceeds 0 dB
The segments under "OVER" light up, and "0.0 dB"
flashes in the display. If these segments light steadily,
sound distortion may occur. To avoid this, keep the
recording level between –12 dB and 0 dB.
To reset the margin indication
Press MARGIN RESET. The margin indication changes
to "- - dB".
4
Stop playing the program source.
5
To start recording, press PAUSE P or PLAY (,
then start playing the program source.
Locating the End of the
Recorded Portion (End Search)
End Search detects a blank section longer than 9
seconds, then automatically rewinds the tape to the
end of the recorded portion, then stops.
Use End Search to start recording from the end of the
recorded portion without creating a blank section on
the tape.
TIMER PREVIOUS NEXT REW FF
= + 0 )
AMS
REC OFF PLAY
STOP PLAY PAUSE REC MUTE
POWER (
p P
REW 0 / FF )
1
With the deck stopped, press REW 0 to rewind
the tape to the beginning .
2
Press FF ).
The deck locates the end of the recorded portion,
then stops.
The deck stops at the beginning of any blank
section that is 9 seconds or longer, or fast-forwards
to the end of the tape if the tape is blank.
z
If you press the REC r button while in a blank
section
The deck automatically rewinds the tape to the
beginning of the blank section and changes to recording
pause. "BLANK" and "WAIT" appear in the display
while the deck is searching for the beginning of the
blank section.
Notes
• End Search does not operate if you press the FF )
button while in a blank section.
• If the tape is blank, the deck merely fast-forwards to the
end of the tape.
10 EN
REC LEVEL
MARGIN START ID
RESET AUTO RENUMBER REHEARSAL 4
3
g 2
WRITE ERASE
1
0
MODE RESET
INPUT REC MODE SBM PHONES
STANDARD
REC OPEN/CLOSE ANALOG 48 kHz
ON
§ OPTICAL 44.1kHz
R r OFF
COAXIAL LONG

Setting the Recording Mode

You can select either of two recording modes—
standard or long—in the following cases.
• When recording an analog input signal with the
INPUT switch set to ANALOG
• When recording a digital input signal with a
sampling frequency of 32 kHz with the INPUT
switch set to OPTICAL or COAXIAL.
TIMER PREVIOUS NEXT REW FF
= + 0 )
AMS
REC OFF PLAY
STOP PLAY PAUSE
POWER p ( P
Set REC MODE to select the recording mode.
The following table shows the selectable recording
modes and corresponding REC MODE position and
sampling frequency for various input signals.
Input signal
Analog
L R
5
6
7
8
9
10
PHONE LEVEL
0 10
Digital (32 kHz)
Digital (44.1 kHz)
Digital (48 kHz)
The recording time in long-play mode (the REC
MODE switch set to LONG) is twice as long as
standard-play mode.
REC LEVEL
MARGIN START ID
RESET AUTO RENUMBER REHEARSAL 4
3
g 2
WRITE ERASE
1
0
MODE RESET
INPUT REC MODE SBM PHONES
STANDARD
REC MUTE REC OPEN/CLOSE ANALOG 48 kHz
ON
OPTICAL 44.1kHz
R r §
OFF
COAXIAL LONG
REC MODE
REC MODE Recording mode
position
STANDARD Standard play
(48 kHz) (48 kHz)
STANDARD
Standard play
(44.1 kHz)
(44.1 kHz)
Long play (32 kHz)
LONG
STANDARD
(48 kHz)
Standard play
(32 kHz)
STANDARD
(44.1 kHz)
LONG Long play (32 kHz)
STANDARD
(48 kHz)
Standard play
(44.1 kHz)
STANDARD
(Standard play
(44.1 kHz)
only)
LONG
STANDARD
Standard play
(48 kHz)
(48 kHz)
STANDARD
(Standard play
(44.1 kHz)
only)
LONG
3-856-761-11(2)
L R
5
6
7
8
9
10
PHONE LEVEL
0 10