Playback Using A Timer (Timer Playing); Writing Sub Codes; About Sub Codes; Writing Start Ids During Recording - Sony DTC-A6 Bedienungsanleitung

Playback Operations Playback Operations
Playback Using a Timer
(Timer Playing)
By connecting a timer (not supplied) to the deck, you
can start and stop playback operations at specified
times. For further information, refer to the instructions
that came with the timer.
TIMER PREVIOUS NEXT REW FF MODE RESET
= + 0 )
AMS
REC OFF PLAY
STOP PLAY PAUSE REC MUTE REC
POWER
p ( P R r
TIMER
1
• To specify the time for the start of playing, do
Steps 1 to 3 of "Playing a DAT" on page 8.
• To specify the time for the end of playing, do
Steps 1 to 4 of "Playing a DAT" on page 8.
• To specify the time for the start and end of
playing, do Steps 1 to 3 of "Playing a DAT" on
page 8.
2
Set TIMER on the deck to PLAY.
3
Set the timer as required.
• When you have set the time for the start of
playback, the deck turns off. When the
specified time arrives, the deck turns on and
after about 10 seconds starts playing.
• When you have set the time for the end of
playback, the deck continues playing, then
when the specified time arrives, the deck stops
playing and turns off.
• When you have set the time for both the start
and end of playback, the deck turns on. When
the starting time arrives, the deck turns on and
after about 10 seconds, playback starts. When
the ending time arrives, the deck stops playing
and turns off.
4
After using the timer, set TIMER on the deck to
OFF.
EN
14

Writing Sub Codes

About Sub Codes

In the DAT format, sub codes (i.e., control codes such
as start IDs and program numbers) can be written on
the tape along with the audio signal. These sub codes
allow you to use AMS (see page 13) or Direct Access
(see page 13). Since sub codes are written on the tape
separately from the audio signal, they have no effect on
the audio signal.
REC LEVEL
L R
MARGIN START ID
5
RESET AUTO RENUMBER REHEARSAL 4 6
3 7
g
2 8
WRITE ERASE 1 9
0 10
INPUT REC MODE SBM PHONES PHONE LEVEL
STANDARD
OPEN/CLOSE ANALOG 48 kHz
ON
OPTICAL 44.1kHz
§
COAXIAL LONG OFF
0 10
Start IDs
Start IDs indicate the start of a track, and therefore
allow you to locate the position of a track precisely.
The start IDs are 9 seconds in length (18 seconds in
long-play mode) to enable easy detection during fast-
forwarding or rewinding.
Program numbers
Program numbers serve as track numbers. Occupying
the same position as start IDs, a program numbers
allow you to locate specific tracks.
Notes
• The STOP p and PAUSE P buttons do not work during
the writing of sub codes.
• Writing and erasing of start IDs and renumbering of
program numbers are impossible if the record-protect hole
on the DAT cassette is open (see page 7).
Writing Start IDs During
Recording
You can write start IDs either manually or
automatically anytime during recording.
TIMER PREVIOUS
=
REC OFF PLAY
STOP
POWER
p
PLAY ( PAUSE P
Track Track Track
Start ID
MARGIN START ID
RESET AUTO RENUMBER REHEARSAL
g
WRITE ERASE
NEXT REW FF MODE RESET
+ 0 )
AMS
INPUT REC MODE SBM
STANDARD
PLAY PAUSE REC MUTE REC OPEN/CLOSE ANALOG 48 kHz
ON
OPTICAL 44.1kHz
( P R r § OFF
COAXIAL LONG
START ID AUTO WRITE
3-856-761-11(2)
REC LEVEL L R
5
4 6
3 7
2 8
1 9
0 10
PHONES PHONE LEVEL
0 10