Additional Information; Troubleshooting - Pioneer DJM-2000nexus Bedienungsanleitung

Additional information

Troubleshooting

! Incorrect operation is often mistaken for trouble or malfunction. If you think that there is something wrong with this component, check the points
below. Sometimes the trouble may lie in another component. Inspect the other components and electrical appliances being used. If the trouble
cannot be rectified after checking the items below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.
! The player may not operate properly due to static electricity or other external influences. In such cases, normal operation may be restored by
unplugging the power cord then plugging it back in.
Problem
The power is not turned on.
No sound or small sound.
Digital sound cannot be output.
Distorted sound.
Can't crossfade.
Can't fader start a DJ player.
BEAT EFFECT function does not work.
[INST FX] does not work.
Can't use an external effector.
Distorted sound from an external
effector.
Tempo (BPM) cannot be measured or
measurement value of tempo (BPM) is
implausible.
Measured tempo (BPM) differs from
tempo indicated on CD.
MIDI sequencer does not synchronize. Is the MIDI sequencer's sync mode set to Slave?
MIDI control does not work.
This unit is not recognized after it has
been connected to a computer.
Sound of a computer cannot be
output from this unit.
Nothing happens when touch panel
is pressed.
Effect sound cannot be monitored
even when the [CUE] button for [BEAT
EFFECT] is pressed.
28
En
Check
Is the power cord properly connected?
Is the [CD/DIGITAL, PHONO, LINE, USB */*]
switch set to the proper position?
Are the [CD, DIGITAL] switches on the rear panel
properly set?
Are the connection cables properly connected?
Are the terminals and plugs dirty?
Is the [MASTER ATT.] switch on the rear panel set
to [–6 dB], etc.?
Is the digital audio output's sampling frequency
(fs) suited for the specifications of the connected
device?
Is the sound level output from the [MASTER] chan-
nel appropriately set?
Is the level of audio input to each channel properly
set?
Are the CROSS FADER ASSIGN (A, THRU, B)
selector switches properly set?
Is [FADER START] set to [OFF]?
Is the DJ player properly connected to the
[CONTROL] terminal?
Is the DJ player properly connected to the [LINK]
terminal?
Are the audio cables properly connected?
Are the [CH SELECT] buttons properly set?
Is the [FILTER] control set to the proper position?
Is the [ON/ OFF] button for [BEAT EFFECT] set
to [ON]?
Is the external effector properly connected to the
[SEND] or [RETURN] terminal?
Is the external effector's audio output level set to
an appropriate level?
Is the audio input level too high or too low?
—
Does the MIDI sequencer you are using support
MIDI timing clocks?
Is the MIDI channel turned on?
Are the MIDI settings properly set?
Is the driver software properly installed on your
computer?
Are this unit and computer properly connected?
Are the audio output device settings properly set?
Is this unit's input selector switch properly set?
Touch panel's calibration is off.
—
Remedy
Plug in the power cord to an AC outlet.
Switch the [CD/DIGITAL, PHONO, LINE, USB */*] switch to the channel's input
source. (page 12)
Set the [CD, DIGITAL] switches according to the devices to be played. (Page 12)
Connect the connection cables properly. (page 7)
Clean the terminals and plugs before making connections.
Switch the [MASTER ATT.] switch. (page 6)
On the [CLUB SETUP] screen, set [DIGITAL SAMPLING RATE] according to the
specifications of the connected equipment. (page 27)
Adjust the [MASTER] control so that the master channel level indicator lights at
around [0 dB] at the peak level. (Page 12)
Set [MASTER ATT.] to [–3 dB] or [–6 dB]. (page 6)
Adjust the [TRIM] control so that the channel level indicator lights at about
[0 dB] at the peak level. (Page 12)
Set the [CROSS FADER ASSIGN (A, THRU, B)] selector switches for the different
channels properly. (Page 12)
At the [USER SETUP] screen, set [FADER START] to [ON]. (page 13)
Connect the [CONTROL] terminal and DJ player using a control cord. (page 7)
Connect the DJ player to the [LINK] terminal properly using a LAN cable. (page
7)
Connect this unit's audio input terminals and the DJ player's audio output
terminals by audio cable. (page 7)
Press the [CH SELECT] button(s) to select the channel(s) to which you want to
add the effect.
Turn the [FILTER] control clockwise. (page 18)
Press [ON/OFF] for the BEAT EFFECT to turn [SEND/RETURN] on. (page 18)
Connect the external effector to the [SEND] and [RETURN] terminals. (page 7)
Adjust the external effector's audio output level.
Adjust the [TRIM] control so that the channel level indicator lights at about
[0 dB] at the peak level. (Page 12)
For some tracks, it may not be possible to measure the tempo (BPM). Use the
[TAP] button to input the tempo manually. (page 18)
The values may differ slightly due to the different ways in which the BPM is
measured.
Set the MIDI sequencer's sync mode to Slave.
MIDI sequencers not supporting MIDI timing clocks cannot be synchronized.
Press the [ON/ OFF] button for [MIDI]. (page 19)
To operate DJ software with this unit, this unit's MIDI messages must be
assigned to the DJ software you are using. For instructions on assigning mes-
sages, see your DJ software's operating instructions.
Install the driver software. If it is already installed, reinstall it. (page 8)
Connect this unit and computer using a USB cable. (page 8)
Select this unit with the audio output device settings. For instructions on making
settings for your application, see your application's operating instructions.
Set the channel's input selector switch to the [USB */*] position. (Page 12)
Adjust the touch panel with the [TOUCH PANEL] settings at the [CLUB SETUP]
screen. (page 27)
The circuit that generates the echo for the [ECHO], [REVERB], [ROLL],
[SLIP ROLL] and [REV ROLL] effect sounds is positioned after the effect circuit,
so the effect sound cannot be monitored. This is not a malfunction.