Additional Information; Troubleshooting - Pioneer DJM-T1 Bedienungsanleitung

Additional information

Troubleshooting

! Incorrect operation is often mistaken for trouble or malfunction. If you think that there is something wrong with this component, check the points below. Sometimes the
trouble may lie in another component. Inspect the other components and electrical appliances being used. If the trouble cannot be rectified after checking the items
below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.
! The player may not operate properly due to static electricity or other external influences. In such cases, normal operation may be restored by unplugging the power cord
then plugging it back in.
Problem
The power is not turned on.
This unit is not recognized.
Music files cannot be played.
No tracks are displayed in the [TRACK] area. Have the music files been properly imported?
Volume of device connected to [AUX IN]
terminals is low.
Distorted sound.
Sound being played is interrupted.
Sound of an external device or microphone
cannot be output.
No sound is produced.
No sound or small sound.
BPM or overall waveform is not displayed.
[SYNC] function does not work.
[SYNC] function does not work even when
files are analyzed.
Deck area display is small.
[SINGLE/GROUP] selector button does not
work.
30
En
Check
Is the power cord properly connected?
Is the [ON/OFF] switch for power supply set to [ON]?
Is the included USB cable properly connected?
Is [CTRL] lit in TRAKTOR?
—
Are the music files damaged?
Have you selected a [Playlists] or [FAVORITES] slot that
does not contain any tracks?
Is the [LEVEL] control on the front panel set to the proper
position?
Are the [MAIN VOL] and [GAIN] controls of TRAKTOR set
to the proper positions?
Is the audio level being input to the [AUX IN] and [MIC]
terminals set to a suitable level?
Is the sound level output from the [MASTER] channel
appropriately set?
Is the level of audio input to each channel properly set?
Are the included power cord and the included USB cable
properly connected?
Is the audio latency value suitable?
Is the [INPUT SELECT] switch on the front panel set to the
[OFF] position?
Are the connection cables properly connected?
Is the included USB cable properly connected?
Are terminals or plugs dirty?
Is the [UTILITY (WAKE UP)] button's indicator flashing at
4-second intervals?
Are [Audio Setup], [Output Routing] and
[Input Routing] in TRAKTOR properly set?
Are the connected components and amplifiers properly
set?
Is the [CD, PHONO, USB] input selector switch set to the
proper position?
Is [MASTER ATT.] set to [–6 dB]?
Has the music file been analyzed?
Have the music files been properly imported?
Has the music file been analyzed?
Is [BEAT MARKER (Grid)] set for hot cue?
—
—
Remedy
Plug in the power cord to an AC outlet.
Set the [ON/OFF] switch for power supply to [ON].
Connect the included USB cable properly. (page 11)
Press any button other than one in this unit's mixer section and check that [CTRL] lights in
TRAKTOR.
Check that [Pioneer. DJM-T1] is selected at [Preferences] > [Controller Manager] >
[Device Setup] > [Device]. (page 25)
Play music files that are not damaged.
Import the music files properly. (page 14)
Select a [Playlists] or [FAVORITES] slot that contains tracks.
Adjust the [LEVEL] control on the front panel according to the connected device. (page 23)
Adjust the [MAIN VOL] and [GAIN] controls while watching the [MAIN] level indicator in
TRAKTOR.
Set the audio level input to the terminals to a suitable level for the connected devices.
Adjust the [MASTER LEVEL] control so that the master channel level indicator lights at
around [0 dB] at the peak level. (page 17)
If the sound is distorted even when the [MASTER LEVEL] control is adjusted, set [MASTER
ATT.] to [–6 dB]. (page 11)
Adjust the [TRIM] control so that the channel level indicator lights at about [0 dB] at the peak
level. (page 17)
The sound will be interrupted if the included power cord or the included USB cable is discon-
nected from the main unit during playback.
Properly fasten the included USB cable to the cord hook on the main unit. (page 11)
When using Windows, open the [ASIO] tab in the settings utility and set the audio latency to
a suitable value. (page 26)
When using a Macintosh computer, set [Preferences] > [Audio Setup] > [Latency] in
TRAKTOR to a suitable value.
Set the [INPUT SELECT] switch to the [AUX] position when using an external device, to the
[MIC] position when using a microphone. (page 23)
Connect the connection cables properly. (page 11)
Connect the computer and this unit directly using the included USB cable. USB hubs cannot
be used. (page 11)
Wipe any dirt off terminals and plugs before connecting.
Install the driver software properly on the computer. (page 9)
Check that [Preferences] is set as shown below. (Page 25)
[Audio Setup] > [Audio Device] > [PIONEER DJM-T1 (Core Audio)] (Mac OS X) or
[PIONEER DJM-T1 ASIO (ASIO)] (Windows)
[Output Routing] > [Output Deck A] [L] > [1.PIONEER DJM-T1 OUT 1] and [R] >
[2.PIONEER DJM-T1 OUT 2]
[Output Routing] > [Output Deck B] [L] > [3.PIONEER DJM-T1 OUT 3] and [R] >
[4.PIONEER DJM-T1 OUT 4]
[Input Routing] > [Input Deck A] [L(Mono)] > [1.PIONEER DJM-T1 IN 1] and [R] >
[2.PIONEER DJM-T1 IN 2]
[Input Routing] > [Input Deck B] [L(Mono)] > [3.PIONEER DJM-T1 IN 3] and [R] >
[4.PIONEER DJM-T1 IN 4]
When using Mac OS X, replace the numbers following [X.PIONEER DJM-T1 OUT] and
[X.PIONEER DJM-T1 IN] above with numbers [0] to [3] when making the settings.
Set the external input selection and volume on the components and amplifiers properly.
Switch the [CD, PHONO, USB] input selector switch and switch the channel's input source.
(page 17)
Set [MASTER ATT.] to [0 dB]. (page 11)
Put a check at [Preferences] > [File Management] >
[Analyze new tracks when loading into deck], then reload the track in the deck.
Reimport the music files and load them in the decks. (page 14)
If music files cannot be analyzed automatically, input the [Beat Grid] manually.
Set at least one [BEAT MARKER] to [Grid].
Put a check at [Preferences] > [File Management] >
[Set Beat-Grid when detecting BPM], then reload the track in the deck.
Double-click the track information display section (the part where the track name, BPM, etc.,
are displayed) in the deck area.
The [Single] mode cannot be selected with TRAKTOR SCRATCH DUO 2.
If you upgrade to TRAKTOR SCRATCH PRO 2, the effect panel can be switched to the [Single]
mode.